HP laser printer ERROR problems
- Share
- publisher
- jacky
- Issue Time
- Aug 17,2011
The following accessories spot sales, due to a wide range of products, the model is not listed please contact us.
Sales Email:sales@printerparts-hp.com Engineer Email:Jacky@printerparts-hp.com
HP laser printers, mostly based on liquid crystal display panel, you can quickly identify the cause of the
malfunction, the following list of common error codes and their interpretation.
1 common error code information to explain the lifting method to display information
13.1 paper jam or a 13.2 paper jam in paper feed part is delayed or stopped
1) determine the carton are properly installed;
2) determine whether the paper part of the no obstruction;
3) Check the PS402, PS403 is working properly, if necessary, be related to sensor replacement
13.5 paper jam or a 13.6 paper jam
Paper in the fuser section is delayed or stopped
1) determine the transfer roller and the conveyor belt to work properly;
2) to determine the feeding path is no obstruction;
3) Check the PS1307 is working correctly, if necessary, replace the sensor to be
13.10 paper jam
Paper in the paper suction area is delayed or stuck
1) Check the feeder part of the paper whether there is obstruction;
2) Check the feeder PS1701, PS1703 sensor is reset, if necessary, replace the relevant sensors
13.20 paper jam or 13.21 paper jam
Paper is jammed in the feeding path, or the printer cover is opened
1) Check the feeding path, clear of obstructions;
2) Check whether all components of feeding reset (including the roof is covered);
3) Check all the sensors on the feeding path is reset, if necessary, be replaced
20 insuffient memory
Printer to accept a lot of data beyond the scope of the printer's memory
1) Press [GO] button to continue printing (some print content may be lost);
2) increase the printer memory 21 page too comlex
Too complex to print the contents of the
1) Press [GO] button to continue printing (some print content may be lost);
2) PAGE PROTECT is set to AUTO 22 EIOхbuffer overflow sent to the EIO peripherals specified by the data too much [GO] button to clear the information (transmitted data will be lost)
41.3 UNEXPECTED PAPER SIZE
Paper type settings do not match the paper type set correctly
50 .* FUSER ERROR fuser error, its * value as follows:
A low heating temperature
2 fuser warm-up protection
3 high heating temperature
4 power supply voltage instability
5 heating components do not match
1 Turn off the power, 20 minutes after the start;
2 Reinstall the fuser;
3 Turn off the power, remove the fuser, check the J1307-1 and J1307-2 and J1308-1 and J1308-2 is connected, such as unreasonable, the replacement of the other hot components
51 .* PRINTER ERROR laser scanning error, * values ??as follows:
A laser detection error
2 Laser error 1 restart; 2 lasers and associated re-install the cable;
3 Replace the laser
52 .* PRINTER ERROR laser scanning speed does not match the * value as follows:
1 scan 2 scan starting rotation error 1 error restart;
2 Reinstall the laser and associated cables;
3 Replace the laser
53.xy.zzPRINTER ERROR additional memory errors, where xyz following meanings: X = DIMM type 0 = ROM 1 = RAM y = Device location of 1-3 that the wrong memory slot location zz = Error number 0 = does not support the installation of 1 = incompatible RAM memory installed 2 = does not support the installation of the Model 3 = RAM memory test failed 4 = exceeds the maximum range of RAM, ROM, 5 = more than the maximum range of 6 = Invalid DIMM speed 7 = DIMM reported error signal 8 = DIMM RAM parity error 9 = ROM address mapping error 10 = DIMM address conflict 11 = PDC XROM out of bounds 12 = Unable to complete the memory buffer
1 Turn off the power, re-install into the memory;
2 switching into the memory location;
3 Replace the memory error
55 PRINTER ERROR internal communication error
1 Check the power position
(2) replace the interface board
3 Replace DC controller board
56 * PRINTER ERROR temporary printing error, * values, said:
1 incorrect input or additional devices are connected wrong
2. Incorrect output 1. Restart the printer; 2 Check the printer configuration; 3 correction to connect additional equipment
57 PRINTER ERROR fan error
1 Check printer's fan is correctly access and is being obstructions stuck;
2 Replace the fan
59 .* PRINTER ERROR motor error, * values ??as follows:
0 Motor error
1 motor startup error
2 motor running error 1. Restart the printer; 2 to determine the normal operation of the connected gear; 3 to determine the motor cable is correctly connected into the 4 replacement motor
62 .* PRINTER ERROR printer memory error, * values ??as follows: 0 = Internal memory 1-3 = DIMM slot 1-3
1. Reinstall into the memory;
2 switch mounting position;
3 Insert the memory replacement
64 PRINTER ERROR receive data buffer error
1 Restart the printer;
(2) replace the interface board
66 xx.yy PRINTER ERROR external misfeeds, XY describes the equipment used as 1stX = number 2ndX = device type: a) input device b) output device c) packing / binding equipment yy = wrong device number 1. Restart printer; 2 check all the cables; 3. reinstall the external feed equipment
79 PRINTER ERROR printer detected an error
1 Restart the printer;
(2) to determine whether the software used in print and printer to match;
3 replacement transmission cables and power supply;
4. Remove a DIMM
5 If possible, use the parallel port to transfer data;
6. Removal of EIO devices;
7 Replace interface card
[Bit] from the original network, reproduced, please retain the original link: http://oa.chinabyte.com/printer/313/11383813.shtmlHP series of laser printers, mostly based on liquid crystal display panel, you can quickly identify the cause of the malfunction, the following list of common error codes and their interpretation.
1 common error code information to explain the lifting method to display information
13.1 paper jam or a 13.2 paper jam in paper feed part is delayed or stopped
1) determine the carton are properly installed;
2) determine whether the paper part of the no obstruction;
3) Check the PS402, PS403 is working properly, if necessary, be related to sensor replacement
13.5 paper jam or a 13.6 paper jam
Paper in the fuser section is delayed or stopped
1) determine the transfer roller and the conveyor belt to work properly;
2) to determine the feeding path is no obstruction;
3) Check the PS1307 is working correctly, if necessary, replace the sensor to be
13.10 paper jam
Paper in the paper suction area is delayed or stuck
1) Check the feeder part of the paper whether there is obstruction;
2) Check the feeder PS1701, PS1703 sensor is reset, if necessary, replace the relevant sensors
13.20 paper jam or 13.21 paper jam
Paper is jammed in the feeding path, or the printer cover is opened
1) Check the feeding path, clear of obstructions;
2) Check whether all components of feeding reset (including the roof is covered);
3) Check all the sensors on the feeding path is reset, if necessary, be replaced
20 insuffient memory
Printer to accept a lot of data beyond the scope of the printer's memory
1) Press [GO] button to continue printing (some print content may be lost);
2) increase the printer memory 21 page too comlex
Too complex to print the contents of the
1) Press [GO] button to continue printing (some print content may be lost);
2) PAGE PROTECT is set to AUTO 22 EIOхbuffer overflow sent to the EIO peripherals specified by the data too much [GO] button to clear the information (transmitted data will be lost)
41.3 UNEXPECTED PAPER SIZE
Paper type settings do not match the paper type set correctly
50.0 *FUSER ERROR fuser error, its * value as follows:
A low heating temperature
2 fuser warm-up protection
3 high heating temperature
4 power supply voltage instability
5 heating components do not match
1 Turn off the power, 20 minutes after the start;
2 Reinstall the fuser;
3 Turn off the power, remove the fuser, check the J1307-1 and J1307-2 and J1308-1 and J1308-2 is connected, such as unreasonable, the replacement of the other hot components
51.0 * PRINTER ERROR laser scanning error, * values ??as follows:
A laser detection error
2 Laser error 1 restart; 2 lasers and associated re-install the cable;
3 Replace the laser
52.0 .* PRINTER ERROR laser scanning speed does not match the * value as follows:
1 scan 2 scan starting rotation error 1 error restart;
2 Reinstall the laser and associated cables;
3 Replace the laser
53.0 xy.zzPRINTER ERROR additional memory errors, where xyz following meanings: X = DIMM type 0 = ROM 1 = RAM y = Device location of 1-3 that the wrong memory slot location zz = Error number 0 = does not support the installation of 1 = incompatible RAM memory installed 2 = does not support the installation of the Model 3 = RAM memory test failed 4 = exceeds the maximum range of RAM, ROM, 5 = more than the maximum range of 6 = Invalid DIMM speed 7 = DIMM reported error signal 8 = DIMM RAM parity error 9 = ROM address mapping error 10 = DIMM address conflict 11 = PDC XROM out of bounds 12 = Unable to complete the memory buffer
1 Turn off the power, re-install into the memory;
2 switching into the memory location;
3 Replace the memory error
55.0 PRINTER ERROR internal communication error
1 Check the power position
(2) replace the interface board
3 Replace DC controller board
56.0 * PRINTER ERROR temporary printing error, * values, said:
1 incorrect input or additional devices are connected wrong
2. Incorrect output 1. Restart the printer; 2 Check the printer configuration; 3 correction to connect additional equipment
57.0 PRINTER ERROR fan error
1 Check printer's fan is correctly access and is being obstructions stuck;
2 Replace the fan
59.0* PRINTER ERROR motor error, * values ??as follows:
0 Motor error
1 motor startup error
2 motor running error 1. Restart the printer; 2 to determine the normal operation of the connected gear; 3 to determine the motor cable is correctly connected into the 4 replacement motor
62.0* PRINTER ERROR printer memory error, * values ??as follows: 0 = Internal memory 1-3 = DIMM slot 1-3
1. Reinstall into the memory;
2 switch mounting position;
3 Insert the memory replacement
64 PRINTER ERROR receive data buffer error
1 Restart the printer;
(2) replace the interface board
66.0 xx.yy PRINTER ERROR external misfeeds, XY describes the equipment used as 1stX = number 2ndX = device type: a) input device b) output device c) packing / binding equipment yy = wrong device number 1. Restart printer; 2 check all the cables; 3. reinstall the external feed equipment
79.0* PRINTER ERROR printer detected an error
1 Restart the printer;
(2) to determine whether the software used in print and printer to match;
3 replacement transmission cables and power supply;
4. Remove a DIMM
5 If possible, use the parallel port to transfer data;
6. Removal of EIO devices;
7 Replace interface card