HP LaserJet M9059 MFP Parts Share Fromhttp://www.printerparts-hp.com publisherJacky Issue Time Sep 14,2012 PartDescriptionR37-7040-000CNScanner_Assembly - IMAGE SCANNER ASSYRG5-6300-070CNADF - ADF main assemblyCC395-67902PC_Board - Formatter (main logic) board - For HP Laserjet M9040/M9050 seriesRH5-3075-090CNPC_Board - Scanner control PC board - Controls the scanner and ADF functions - Connects to all the drive motors in both units and all the sensors in the scanner - Mounts in rear of the scanner towards the left rearC8523-69011PC_Board - Scanner Control PC board - Controls the scanner and ADF functions - Connects to all the drive motors in both units and all the sensors in the scanner - Mounts in rear of the scanner towards the left rearRG1-4386-020CNPower_Supply - Scanner power supply assembly - Includes the power supply electronics, fan, and support bracket - Provides power for the ADF and scanner assemblies - Mounts on the rear of the scanner assemblyC8531-69018Tray - 2,000-sheet high capacity paper feeder assemblyRG5-6307-020CNOptical_Unit - ADF scanner (optical) assembly - Includes the chassis assembly, scanner lens assembly (includes the Charge Coupled Device (CCD)), the scanning lamp, ADF analog processor board, and ADF inverter board - Major portion of the ADF main assemblyC9153-69007Maintenance_Kit - Maintenance Kit - For 220 VAC - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer rollerC9152-69007Maintenance_Kit - Maintenance Kit - For 120 VAC - Replacement Parts after 350k Pages Includes, Fuser Assembly, 7 Feed/Separation Rollers, 2 Pickup Rollers and Transfer rollerQ7719-67951Memory - HP 256MB 100-pin DDR DIMM - Used to add flash memory-based accessory fonts, macros, and patternsC8519-69036Fuser_Assembly - Fuser Assembly - For 220 VAC to 240 VAC - Bonds toner to paper with heatRG5-7778-030CNPower_Supply - Low voltage power supply assembly - For 100-127VAC operation - Mounts on the upper rear of the printerC9153-69006Maintenance_Kit - Maintenance Kit (220V) - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer rollerC8519-69035Fuser_Assembly - Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heatRG5-6263-070CNOptical_Unit - Flatbed scanner optical assembly - Includes the support structure, lamp assembly, charge-coupled devices (CCD) and lens assembly, flatbed analog board, drive belt, and cables - Scans and digitizes documents placed on the flatbed scannerRG5-5750-000CNFuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V OperationRM1-7354-000CNPower_Supply - POWER SUPPLY ASS YRG5-7779-030CNPower_Supply - Low voltage power supply assembly - For 220-240VAC operation - Mounts on the upper rear of the printerC9152-69006Maintenance_Kit - Maintenance Kit - For 120 VAC operation - Replacement parts after 350k pages - Includes fuser assembly, seven feed/separation rollers, two pick-up rollers and transfer rollerC9153-67907Maintenance_Kit - Maintenance Kit - For 220 VAC - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer rollerC8519-69033Fuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 100V to 127V OperationRG5-5684-000CNFuser_Assembly - Fuser Assembly - For 100 VAC to 127 VAC - Bonds toner to paper with heatC9153-67906Maintenance_Kit - Maintenance Kit (220V) - Replacement parts after 350K pages - Includes, Fuser Assembly, seven feed/separation rollers, two pickup rollers and transfer rollerRG5-6275-060CNPickup_Assembly - Paper pickup assembly - Includes the pickup structure pieces, motors, gears, belts, rollers and sloenoid (Does NOT include the ADF main assembly) - Mounts on top of the ADF base assembly towards the left endRG5-5826-090CNLaser_Scanner - Laser/Scanner assembly - Mounts on the support structure in the print engine frame assemblyRG5-5681-090CNPickup_Assembly - Paper input unit - Entire assemblyCC395-60102Control_Panel - Control panel assembly - Control buttons and display located on top front of printerQ6005-67901PC_Board - Copy processor board assembly - Includes the PC board and support carrier frame - Plugs in one of the EIO slots on the printerRF5-3676-000CNGlass - Copyboard glass assembly - Mounts in the frame on top of the scanner assemblyRG5-6272-050CNCover - ADF base cover assembly - Includes the large bottom rectangular support cover for the ADF assembly with front and rear tray guides, the ADF intermediate PC board, cables, sensors, and hingesRG5-5663-060CNRoller - Registration roller assemblyRG5-7780-060CNPC_Board - DC controller board assemblyRG5-5728-100CNPower_Supply - High voltage power supply board0950-4753Hard_Drive - 40GB SATA Hard drive - 5,400 RPM, 2.5 inch form factor, 9.5mm heightC8543XCartridge - HP Ultra-Precise print cartridge (Smart print cartridge) - Will print approximately 30,000 pages based on a 5% print densityRG5-6208-180CNPaper_Input_Unit - Paper Input Unit (PIU) - For tray 4RG5-6235-150CNPC_Board - Controller PC boardQ3701-60020PC_Board - Modem PCA - HP LaserJet analog fax accessory 300C8519-69037Power_Supply - High voltage power supply board - Mounts on the upper rear of the printerCE266-67901Other_Parts - Repl Toner HP LaserJet M9059 MRG5-5643-080CNDelivery - Delivery assembly - Includes the curved plastic structure, various rollers and gears, and the 'L' shaped metal support structure with three fansRG5-5646-070CNDoor - Left door and diverter assemblyRG5-5737-090CNCover - Right cover assembly - Includes all components attached to this doorRG5-5656-080CNDrive_Assembly - Drum feed drive assemblyRG5-6250-040CNPower_Supply - Power supply assemblyRG5-6225-100CNPaper_Path_Module - Vertical registration assemblyRG5-7807-000CNSensor - Sensor assembly - Includes the support plate, number 3 document size sensor (PS4) and cable assembly - Mounts in the bottom of the scanner assembly toward the middleRG5-6266-030CNRoller - Lower delivery roller assembly - Includes the support bracket, shaft, and four rollers - Moves scanned documents from the ADF assembly into the output tray - Mounts on the left end of the scanner assemblyRH7-1622-000CNMotor - Fuser delivery motor (24 VDC) - Provides power for fuser delivery drive assemblyRH7-1656-000CNMotor - Drum feed drive motorRF5-3695-030CNCover - Whiteboard cover assembly - White padded sheet mounted on a rectangular support cover - Mounts on the under side of the ADF assembly/scanner lidQ7718-67951Memory - 128MB, 100-pin, DDR SDRAM DIMM memory moduleRG5-5635-110CNTray - 500-sheet paper cassette - Paper cassette used for tray 2 and tray 3RG5-7789-050CNDrive_Assembly - Fuser delivery drive assembly - Includes gears, motor and microswitch for fuser drive - Also drives delivery rollerQ6006-67901PC_Board - Copy connect board assembly - LVDS adapter board used to interface the flatbed scanner to the copy processor board in the printer - Mounts on the rear of the flatbed scanner assemblyRG5-5647-070CNDelivery - Face-up delivery assemblyQ3726-60101 - COPY CONNECT CABLE-SCANNER 16 INRG5-7896-000CNPC_Board - Paper pickup boardRG5-5719-100CNPC_Board - Memory controller PC Board - Toner cartridgeRH7-1488-030CNMotor - Motor (24 VDC) assembly - Drives the paper pickup roller, feed roller, separation belt assembly, and registration rollers - Mounts at an angle in a bracket on the rear frame of the ADF paper pickup assemblyRH7-1487-020CNMotor - Motor (24 VDC) assembly - Drives the output delivery rollers - Mounts in a bracket about in the center of the rear frame of the ADF paper pickup assemblyRG5-5645-020CNDelivery - Delivery cross member assembly - Includes the 'L' shaped support bracket with the rear delivery fan (Fan 3), front delivery fan (Fan 4), and face down tray fan (Fan 6)RG5-6318-030CNFan - 24VDC cooling fan assembly - Includes fan, filter and metal grill - Mounts on the rear support frame in the left rear corner of the scanner assemblyQ6006-60001PC_Board - Copy connect board assembly - LVDS adapter board used to interface the flatbed scanner to the copy processor board in the printer - Mounts on the rear of the flatbed scanner assemblyRH5-3165-030CNPC_Board - Intermediate PCA board - Located on the scanner assemblyRB2-7947-000CNHinge - ADF HINGERG5-6274-000CNSensor - ADF media width sensor assembly (includes the white sensor gear that mates with the rack gear) - Works with the front and rear width guides - Mounts on the bottom center of the ADF base assembly (behind the copyboard cover assembly)RG5-5809-060CNTray - Multi-purpose Tray - Optional Tray 1 drop down paper input tray assembly only - Includes drop down flip out tray and paper width guidesRG5-5702-050CNCover - Front cover assembly - Large door above trays 2 and 3RB2-5660-000CNCover - Top left cover - Face down paper output cover - Located on the left side portion of the top coverC8085-60541Cartridge - Staple cartridge - Contains 5000 staples - For the add-on staple/stacker unitRG5-6315-000CNCover - Rear ADF cover assembly - Includes the rear ADF electronics cover and the two hinge coversRG5-8009-000CNPC_Board - Cartridge memory controller board - Between ECU and the toner cartridge memory antennaRG5-7806-030CNSensor - Sensor assembly - Includes the support plate, number 3 document size sensor (PS4) and cable assembly - Mounts in the bottom of the scanner assembly toward the middleRG5-6228-060CNDrive_Assembly - Feed drive assembly - Includes the drive motor (M303), support bracket, and the four drive gears - Mounts in the 2,000-sheet paper feeder assemblyRG5-5662-050CNTransfer_Assembly - Transfer roller assembly - Includes both transfer guides and transfer rollerRH7-1661-000CNFan - Tubeaxial fanRG5-6258-040CNSensor - Sensor crossmember assembly - Includes the Black plastic housing, document sensor (PS1), number 1 and 2 document size sensors (PS2 and PS3), home position detector sensor (PS5), and cable assembly - Mounts in the bottom right of the scanner assemblyRG5-6281-020CNRoller - Feed roller assembly - Includes a steel shaft with five rubber rollers, two bushings, a spring, and 'E' clips - Mounts to the left of the paper pickup roller in the bottom of the ADF paper pickup assemblyRG5-6312-030CNFan - ADF cooling fan assembly - Includes the fan assembly, fan housing, and interconnecting cable - Mounts on the left rear of the ADF base assemblyRG5-6227-040CNPaper_Path_Module - Paper path connection assembly - Directs paper from the high capacity input assembly output to the vertical input path on the print engineRG5-5724-050CNHolder - Fuser connector holder assemblyRG5-5741-040CNLifter - Cartridge lifter assemblyRB2-8040-000CNCover - Top cover assembly - 'U' shaped plastic cover - Covers the top of the scanner in the ADF assembly - Mounts on the left end of the ADF assemblyRF5-3319-000CNRoller - Transfer roller - Includes the long black spongy roller, roller shaft, and drive gear - Transfers static charge to the paperRG5-6283-020CNRoller - Pickup roller assembly - Includes a steel shaft with a rubber 'D' shaped roller, drive gear, bushings, sesnor flag, and two retaining clips - Mounts in the bottom of the ADF paper pickup assemblyRG5-5701-000CNCover - Rear cover assemblyRH7-1657-000CNFan - Tubeaxial fan (fan 1) - Provides air to the power supplyRH5-3078-030CNPC_Board - ADF intermediate PC board - Has for cable connectors (J701, J702, J703, and J704) plus the ADF close angle detection sensor - Mounts on top of the ADF base assembly towards the center rearRG5-5651-030CNGuide - Transfer guide assembly (Ribbed plastic piece) - Has slot for the transfer roller assemblyRB2-7648-040CNCover - Front cover for the 2,000-sheet paper feeder assemblyRG5-5722-030CNCable - Main cable harness and holder assemblyRH5-3073-030CNPC_Board - Flatbed intermediate PC Board - Intermediate Board between the scanner control board (J502) and the flatbed analog processor board (J501) - Mounts in the bottom of the scanner housing (below the copyboard glass)RB2-5659-000CNCover - Top right cover - Located on the right side portion of the top coverRF5-3645-000CNCover - Left cover for the 2,000-sheet paper feeder assemblyRG5-5727-030CNReceptacle - A/C power input receptacle module and power switchRB2-7934-000CNCover - Upper front cover - Top of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assemblyRG5-6316-000CNTray - ADF paper output tray - Includes the tray with pull-out extension - Receives scanned pages from the ADF assembly - Mounts on the left side of the ADF/scanner assemblyRG5-6311-000CNGuide - Cable guide assembly - Black plastic channel/cover - Mounts on the rear of the ADF main assemblyCC501-67924Other_Parts - LJ M9040/50 MFP 128MB Flsh ModRG5-5721-000CNCover - Front inside cover - Cover behind front drop down coverRG5-8025-000CNCable - Cable assembly - Fuser power cableRB2-6007-000CNDoor - Left side door - Left cover that diverter assembly attaches toRB2-7933-000CNCover - Lower front cover - Bottom of the protrusion that makes up the control panel housing - Mounts to the front of the scanner assemblyRB2-7649-000CNCover - Right cover for the 2,000-sheet paper feeder assemblyRG5-7787-000CNCable - Upper cable guide assembly - Includes the two upper cables and support bracket - Mounts in the top of the printerRG5-6207-060CNSensor - Paper size sensing assemblyRB2-5690-000CNTray - Face up paper output trayRH7-1623-000CNFan - Controller board tubeaxial fanRH5-3079-030CNPC_Board - ADF sensor PC board assembly - Narrow strip PC board with the two document skew sensors, registration sensor, and timing sensor - Mounts on top of the registration guide assembly in the ADF main assemblyRH7-1481-020CNMotor - Deck drive motor (M303) only - Mounts in the 2,000-sheet paper feeder assemblyRG5-6305-000CNFlag - Registration flag and sensor holder assembly - Activates the document registration sensor on the sensor board on top of the registration guide assembly in the ADF main assemblyRH7-1659-000CNFan - Tubeaxial fanRG5-5654-000CNGuide - Transfer roller guide - Mounts to the top of the base structure of the transfer roller assemblyRG5-6238-020CNPC_Board - Paper size PC boardRH2-5456-000CNCable - Ribbon cable - Connects between the ADF analog processor board (J301) in the ADF assembly and the scanner control board (J102) in the flatbed scanner assemblyRG5-6298-000CNWeight - Weight plate assembly - Solenoid activated plate assembly that drops down during the paper pickup process and pushes against the paper stack on the pickup rollers - Mounts in the ADF paper pickup assemblyRB2-7961-000CNRoller - Paper pickup roller (Only) - Rubber 'D' shaped roller - Mounts on the paper pickup drive shaft in the bottom of the ADF paper pickup assemblyRG5-3850-000CNPlate - Front paper reference plate - Front paper limit plate for 2,000-sheet feederRB2-7988-000CNBelt - Separation belt - Gray rubber belt between the separation drive shaft and the stationary shaft - Mounts towards the entrance of the ADF paper pickup assembly (four used)FH7-7424-000CNSensor - Scanner media size sensor - Media width size sensor (PS4) for the flatbed scannerRB2-5682-000CNCover - Lower right front corner cover for tray 2 and 3RF5-3689-020CNFlapper - Rear flapper arm - Part of the paper separation mechanism for the paper pickup assembly - Mounts just in front of the rear separation belts in the ADF assemblyRB2-8054-000CNCover - Left side cover - Serves as the mounting bracket for the ADF paper output tray - Mounts on the upper left side of the scanner assemblyRB3-0304-050CNCaster - Front swivel caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used)RH7-1658-000CNFan - Tubeaxial fan (fan 4) - Mounts on the upper left crossmember on the delivery assemblyRG5-5705-030CNCover - Left upper cover - Small cover above left doorRF5-3688-020CNFlapper - Front flapper arm - Part of the paper separation mechanism for the paper pickup assembly - Mounts just in front of the front separation belts in the ADF assemblyRG5-6203-000CNHolder - CABLE HOLDER ASSYRB2-7678-030CNCaster - Stationary rear caster - Mounts on the bottom frame of the 2,000-sheet paper feeder assembly (two used)RH7-1486-020CNFan - ADF cooling fan (ONLY) - Mounts on the left rear of the ADF base assemblyRG5-6313-030CNGuide - Upper and lower rear cable guides (I/F 2 and 3) - Two of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assemblyRH7-5312-020CNSolenoid - solenoid (24 VDC) assembly - Activates the paper feed shutter assembly - Mounts on the rear frame of the ADF paper pickup assembly towards the rightRB2-5684-000CNCover - Right rear cover - small cover strip on rear side of right cover assemblyRG5-6304-040CNRoller - Upper registration roller guide assembly - Includes the steel shaft with four White rollers mounted in a support frame - Mounts in the lower center of the ADF main assemblyRG5-8034-000CNCable - Fuser Assembly high voltage cable and connectorsRG5-5700-030CNKnob - Fuser jam removal knobFH7-7423-020CNOther_Parts - SENSOR, DOCUMENT SIZERG5-5740-020CNLatch - Right cover latch handle assemblyRG5-6289-020CNSolenoid - Solenoid (24 VDC) assembly - Includes the solenoid and lever armRB2-8016-000CNShaft - Latching shaft - Long square shaft with a latching hook at one end - Used with the free release latch and release handle to secures the ADF main assembly when the unit is in the operating positionRF5-3644-020CNCover - Rear center cover for the 2,000-sheet paper feeder assemblyRG5-5653-030CNHolder - Transfer roller holder assembly - Includes the base structure, latch, anti-static brush, pressure springs, bushings, and contact springs - Assembly that the transfer roller mounts inRF5-3674-000CNCover - Roller cover - Covers the exit delivery roller on the left side of the scanner assemblyRB2-5687-000CNCover - Lower left cover - Smaller plastic piece below left door and diverter assemblyRG5-5704-040CNLatch - Latch mount assemblyRG5-5715-030CNRail - Right rail assemblyRG5-6229-040CNSensor - Paper volume sensing assemblyRB2-8048-000CNCover - ADF assembly front cover - Mounts on the end of the ADF main assembly structureRB2-8015-000CNHandle - Release handle - Used to open the ADF main assembly from the paper pickup assembly to clear paper jams - Slides on the latching shaft in the top left center of the ADF main assemblyRG5-6206-030CNSwitch - Switch assembly - Custom/standard paper switchRG5-6306-020CNFlag - Timing flag and sensor holder assembly - Activates the two document skew detection sensors and the timing detection sensor on the sensor board on top of the registration guide assembly in the ADF main assembly (three used)RB2-7650-000CNCover - Right rear cover for the 2,000-sheet paper feeder assemblyRG5-5648-020CNDamper - Left door damper assemblyRG5-5811-040CNCover - Service cover assembly - Cover for pickup and separation rollersWG8-5624-000CNSensor - Replacement for part WG8-5362-000CN ORDER WG8-5624-000CN PHOTO-INTERRUPTER TLP1241 Photo-sensor (TLP1241) - Sensor flag activatedRB2-6491-000CNCover - Left upper cover - Small piece above left doorRB2-5685-000CNCover - Left back cover - Narrow strip covering the left rear corner of the printerRH7-5306-000CNFan - Tubeaxial fan (#5) - Provides air to the cartridge areaRG5-5706-000CNCover - Left upper cover assembly - Small rectangular cover that mounts between the top of the printer and the paper output trayRG5-5717-020CNContact - Toner cartridge contact assemblyRG5-6317-000CNHinge - Hinge cover assembly - Flexible hinge with four divisions - Mounts on the rear between the ADF assembly and the scanner assembly (two used)RG5-5779-030CNConnector - Jetlink connector - Connector between Tray 4 and printer engineRG5-5746-030CNLever - Cartridge release lever assemblyRB2-7651-000CNCover - Left rear cover for the 2,000-sheet paper feeder assemblyRB2-8063-000CNCover - Right side cover - 'L' shaped rectangular cover for the right end of the scanner assemblyRG5-5714-020CNRail - Left lower rail assemblyRB2-5653-000CNStrap - Restraining strapRG5-5699-040CNSensor - End paper sensor assembly - Contains Tray 2 and 3 paper length detection switchesRF5-3404-000CNRoller - Separation roller - For tray 1 assemblyRG5-6257-000CNCable - Scanner controller ribbon cables (two cable set) - Interconnects the flatbed intermediate PC board (J504 and 502) to the scanner control PC board (J103 and J105) - Mounts towards the front of the scanner assemblyRB2-5676-000CNCover - Tray 1 blanking coverRG5-5713-020CNRail - Left upper rail assemblyRG5-8013-000CNPC_Board - Delivery assembly PC boardRB2-5683-000CNCover - Lower left front corner cover for tray 2 and 3 - Includes power buttonRB2-7709-020CNCaster - CasterWC4-5136-000CNSwitch - Black toner cartridge switch - Detects when black cartridge is in correct positionRB2-5689-000CNCover - Lower right cover - Small plastic piece below right door assemblyRG5-6285-020CNSensor - Photo-sensor assembly - Includes the sensor and mounting bracket - Paper pickup roller home position sensor - Activated by the sensor flag on the pickup roller assembly - Mounts on the front frame of the ADF paper pickup assemblyRB2-5528-000CNLink - Connector link - Door ajar flagRG5-5718-000CNRail - Cartridge guide rail - Right side toner cartridge guide railRG5-6237-020CNPC_Board - Paper volume sensor boardRG5-7786-000CNCable - Fan control cable assembly - Includes the cable assembly and holder - Mounts on the rear of the printer and routes cable around the DC controller boardRG5-5709-000CNMount - Front pressure mount for toner cartridgeRG5-6239-020CNPC_Board - LED board - Small PC board with two LEDs and a connector - For indicating the operating statusRF5-3403-000CNRoller - Pick-up roller for optional tray 1RG5-8038-000CNCable - Multi-purpose/tray 1 cable assemblyRB2-5813-000CNLever - Custom/standard media size selection switch lever - Mounts on the left side of the 500-sheet paper input trayRF5-3682-000CNGuide - Rear paper guide - Width adjustable side wall for documents placed in the ADF input tray - Mounts on top of the ADF base assemblyXA9-0499-000CNScrew - Screw with captured washer - Used to fasten plastic to metal - M4 X 6mm screwRB2-7762-020CNLever - Paper size switching lever - To adjust paper size in tray (standard or custom size)RB2-5828-000CNHandle - Registration guide handleRB2-5661-000CNRod - ON/OFF switch push rodRB2-8678-000CNFerrite_Assembly - Ferrite core assembly - Large 'doughnut' shaped ferrite for the ribbon cable that connects the scanner control PC board to the ADF analog processor PC boardWC4-5175-000CNSwitch - Micro-switch - Detects when the paper feeder/scanner assembly is open - Mounts in a support bracket on the rear frame of the ADF paper pickup assemblyRB2-5700-000CNLatch - Front cover latch - Roller latch that holds front coverRG5-5735-000CNCable - Power supply cable - Connects between the scanner power supply board and the print engine power supply moduleRB2-5515-000CNRail - Front Fusing RailRF5-3850-000CNFilter - ADF optical unit air filter - Keeps dust particles from contacting the scanning lamp - Mounts on the lower rear of the ADF main assemblyRB2-5516-000CNRail - Rear Fusing RailRB2-5526-000CNGuide - Cartridge guide - Plastic structure with cartridge guide slot molded into it - Mounts on the upper front side of the registration assemblyRF5-3698-000CNGuide - Front paper guide - Width adjustable side wall for documents placed in the ADF input tray - Mounts on top of the ADF base assemblyRG5-5710-000CNMount - Rear pressure mount for toner cartridgeRB2-7935-000CNMount - Glass mount cover - Small plastic piece that covers the mounting hardware used to retain the copyboard glass - Mounts in the recesses on the scanner assembly upper front cover (two used)RB2-8060-000CNCover - Connector cover - Small rectangular piece that extends out from the back of the scanner assembly (two used)RG5-7783-000CNCable - Fan connecting cable - Mounts on the rear of the printerRF5-3338-000CNRoller - Feed separation pick-up roller - Rubber roller on a plastic collar with integrated gear and locking tabRB2-5640-000CNShutter - Laser shutter - Cartridge shutter actuator - Piece that opens cartridge shutter as it is inserted into the printerRB2-5654-000CNHinge - Front cover hingeRB2-8046-000CNGuide - Lower front cable guide (I/F 1) - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assemblyRB2-5570-020CNMount - Door dampener hinge mount - Left side/fuser door dampener mount (two used)RB1-6421-000CNFoot - Chassis foot - Support for right side of printer chassis - Two usedRB2-5522-000CNGuide - Paper pickup guide - Plastic shaft with several fins on it - Mounts on the upper right side of the print engine frame assemblyRB2-8002-000CNFlag - Flag lever - Lever half of the sensor flag for detecting when the ADF input tray is empty - Flag part hangs down at the entrance to the ADF paper pickup assemblyRB2-7927-000CNClip - Glass mounting alignment clip - Used to properly align the copyboard glass in the scanner assembly cover frame - Mounts in the left rear corner of the frame (one used)RB2-5523-000CNContact - Fuser electrical contact leaf springRB2-8017-000CNLatch - Release latch - Curved plastic latch that slides on the latching shaft - Secures the ADF main assembly when the unit is in the operating position - Mounts on the front of the ADF main assemblyRB2-7943-000CNLever - Sensor lever - Rotating arm with a flag at one end that protrudes through the ADF base and another at the other end that activates one of the media length sensors - Mounts on the bottom center of the ADF base assembly (two used)RB2-5697-000CNCover - Right front inside corner cover5851-2583Cover - EIO slot cover - Installs on formatter boards without JetDirect PCAVD7-2895-001CNFuse - Fuse - 5A, 250 VAC - Mounts in the flatbed scanner power supply assemblyRB2-5656-000CNPin - Pin - Located on the front cover assembly next to the roller action latchRG5-5752-000CNCable - Control panel cable assembly - Connects between the control panel and the intermediate PC boardRB2-7978-000CNFlag - Flag lever - Sensor activator half of the sensor flag for detecting when the ADF input tray is empty - Activates the sensor on the rear wall of the ADF paper pickup assemblyRF5-3340-000CNRoller - Paper pick-up and feed roller assembly - Rubber roller with drive gearRB2-8681-000CNGuide - Lower internal cable guide (I/F 5) - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assemblyRB2-5529-000CNFoot - Chassis foot - Support for left side of printer chassis - Two usedRB2-7928-000CNClip - Glass mounting clip - Used to retain the copyboard glass in the scanner assembly cover frame - Mounts in the left front, right front, and right rear corners of the frame (three used)RB2-5517-020CNMount - Front Fuser Assembly mountRB2-7999-000CNWeight - Weight plate (Only) - Black plastic plate that drops down during the paper pickup process and pushes against the paper stack on the pickup rollers - Mounts in the ADF paper pickup assemblyRS6-2298-020CNSpring - Tension springXB4-5401-009CNScrew - Machine screw with attached washer - M3, 10mm - Used to hold plastic to metalRB2-5845-000CNKnob - Jam removal knobRB2-8682-000CNGuide - Upper internal cable guide (I/F 6) - Arm shaped ribbon cable retainer - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assemblyXA9-1495-000CNScrew - Wafer head machine screw - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metalXA9-0912-000CNScrew - Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metalXA9-0994-000CNScrew - Screw - M4 x 6mm longXA9-1448-000CNScrew - Screw - M4 X 8mm longXA9-1466-000CNScrew - Machine screw with captured washer - M3 X 29.5mm longRB2-5518-020CNMount - Rear Fuser Assembly mount5851-1885Other_Parts - PLUG-FAXRS6-2299-000CNSpring - Shutter arm spring - Provides tension for shutter armRS6-2302-000CNSpring - Compression spring - Provides tension for ON/OFF switchRS6-2499-000CNSpring - SPRING TENSIONXA9-1500-000CNScrew - M3 pan-head Phillips screw with flat washer - 8mm longXB2-6300-607CNScrew - Screw - M3 X 6mm longRS5-0708-000CNGear - 21 tooth gearRS5-9099-000CNScrew - Stepped screw - Larger shoulder screw used to fasten the left side cover to the frame of the 2,000-sheet paper feeder assembly (two used)RS6-2285-000CNSpring - Tension springRS6-2296-000CNSpring - Laser shutter spring - Provides tension for laser shutterRB2-5816-000CNSpring - Torsion spring - Provides tension for paper selector switchRB2-6495-000CNClip - Holder clip lock - Secures the ADF/Scanner assembly to the top of printer (four used)RB2-7920-000CNPlate - Ground plate - Small plate with two tangs - Grounds the end of the carriage rod for the scanner optical assembly - Mounts on the right end of the scanner assembly towards the rearRB2-6035-000CNFlag - Sensor flag - Long rod with forked flag toward one end and curved flag at the otherRB2-6036-000CNFlag - Sensor flag - Short rod with two flat flags and a curved end flagRB2-6037-000CNFlag - Sensor flag - Short rod with two flags on itRB2-6042-000CNSpring - Torsion spring - Provides tension for bin full flagRB2-6077-000CNLever - Microswitch lever - Activates interlock switches from both the front and left doorsRH2-5445-000CNCable - High voltage power supply ribbon cableRB2-5547-000CNLatch - Left side alignment latch for front doorRB2-5639-000CNArm - Shutter armRB2-5675-000CNCap - Right cover capRB2-5679-000CNPlate - Right side lock plateRG5-5764-000CNCable - Cable assembly - Grounding cable for tray 1RG5-5736-000CNCable - Grounding cable - Grounding cable for ADF/scanner assemblyRB2-8693-000CNHolder - ADF stop holder - White plastic 'T' shaped bumper that limits travel of the ADF main assembly mechanism - Mounts in the upper left front corner of the lower feed mechanismRB2-8094-000CNOther_Parts - CLAMP CABLERB2-8047-000CNGuide - Upper front cable guide (I/F 4) - Curved plastic piece - One of six pieces that form the pivioting cable guide from the ADF assembly to the scanner assembly - Mounts on the left rear of the ADF assemblyRB2-7989-000CNSpacer - Support spacer - Used to keep the separation belts tight between the drive shaft and the stationary shaft in the separation assembly - Mounts in the ADF paper pickup assembly (three used)RB2-7990-000CNHolder - Spring holder - Small Black plastic piece that holds the leaf spring against the stationary shaft in each spacer in the separation assembly - Mounts in the ADF paper pickup assembly (three used)RB2-7991-000CNSpring - Leaf spring - Used to lock the spacer between the drive shaft and the stationary shaft in the separation assembly - Mounts in the ADF paper pickup assembly (three used)Q7815-67901Other_Parts - HEBREW FONT USB SOLUTIONQ7815-67902Other_Parts - CYRILLIC FONT USB SOLUTIONQ7815-67903Other_Parts - GREEK FONT USB SOLUTIONQ7815-67904Other_Parts - ARABIC FONT USB SOLUTIONRH7-1485-020CNMotor - 24VDC scanner stepper motor - Provides the drive to move the scanner optical assembly back and forth - Mounts in the right rear of the scanner assemblyQ7718-67901Memory - 128MB, 100-pin, DDR DIMM memory moduleQ7719-67901Memory - 256MB, 100-pin, DDR DIMM memory module0515-4257Screw - Pan head taptite screw with washer - M3.0 x 0.5, 6mm long, Number 2 Phillips0515-4679Screw - M3 pan-head phillips screw with washer - 6mm longVD7-9825-000CNFuse - Fuse - 5A, 250 VAC - Mounts in the flatbed scanner power supply assemblyU2014ECare_Pack - HP Network Install high-end LaserJet Multifunction printer ServiceU9877ECare_Pack - HP Maintenance Kit Replacement LaserJet 90xx/90xxMFP/M90xxMFP Fuser 110V ServiceUP833ECare_Pack - HP 5 year Next business day response onsite LaserJet M9059 MFP Hardware SupportUP845ECare_Pack - HP 3 year Next business day response onsite LaserJet M9059 MFP Hardware SupportUP847PECare_Pack - HP 1 year Post-Warranty Next business day response onsite LaserJet M9059 MFP Hardware SupportUP848ECare_Pack - HP 4 year Next business day response onsite LaserJet M9059 MFP Hardware Support5851-2972Other_Parts - RAIL, LEFT SNAP5851-2973Other_Parts - RAIL, RIGHT SNAPCC395-60116Overlay - Control panel overlay - Snaps on top of the control panel assembly (Czech)CC395-60117Overlay - Control panel overlay - Snaps on top of the control panel assembly (Hungarian)CC395-60120Overlay - Control panel overlay - Snaps on top of the control panel assembly (Korean)CC395-60121Overlay - Control panel overlay - Snaps on top of the control panel assembly (Japanese)CC395-60122Overlay - Control panel overlay - Snaps on top of the control panel assembly (Turkish)CC395-60123Overlay - Control panel overlay - Snaps on top of the control panel assembly (Hebrew)CC395-60124Overlay - Control panel overlay - Snaps on top of the control panel assembly (Greek)CC395-60125Overlay - Control panel overlay - Snaps on top of the control panel assembly (Arabic)CC395-60126Overlay - Control panel overlay - Snaps on top of the control panel assembly (Thai)CC395-60127Overlay - Control panel overlay - Snaps on top of the control panel assembly (Croatian)CC395-60128Overlay - Control panel overlay - Snaps on top of the control panel assembly (Romanian)CC395-60129Overlay - Control panel overlay - Snaps on top of the control panel assembly (Slovak)CC395-60130Overlay - Control panel overlay - Snaps on top of the control panel assembly (Slovenian)CC395-60135Overlay - Control panel overlay - Snaps on top of the control panel assembly (Catalan)CC395-60103Overlay - Control panel overlay - Snaps on top of the control panel assembly (English)CC395-60104Overlay - Control panel overlay - Snaps on top of the control panel assembly (French)CC395-60105Overlay - Control panel overlay - Snaps on top of the control panel assembly (Italian)CC395-60106Overlay - Control panel overlay - Snaps on top of the control panel assembly (Dutch)CC395-60107Overlay - Control panel overlay - Snaps on top of the control panel assembly (Spanish)CC395-60108Overlay - Control panel overlay - Snaps on top of the control panel assembly (for use in the Netherlands)CC395-60109Overlay - Control panel overlay - Snaps on top of the control panel assembly (Portuguese)CC395-60110Overlay - Control panel overlay - Snaps on top of the control panel assembly (Norwegian)CC395-60111Overlay - Control panel overlay - Snaps on top of the control panel assembly (Swedish)CC395-60112Overlay - Control panel overlay - Snaps on top of the control panel assembly (Finnish)CC395-60113Overlay - Control panel overlay - Snaps on top of the control panel assembly (Danish)CC395-60114Overlay - Control panel overlay - Snaps on top of the control panel assembly (Polish)CC395-60115Overlay - Control panel overlay - Snaps on top of the control panel assembly (Russian)CE770-67914Other_Parts - LJ M9040/50 MFP 1GB Flsh Mod 5C9153-67908Other_Parts - Exch.Fuser Assy-220VC8531-67908Tray - Tray 4 assembly (complete) - 2,000-sheet high capacity paper feeder assembly