HP Color LaserJet CM6040f MFP Parts Share Fromhttp://www.printerparts-hp.com publisherJacky Issue Time Oct 13,2012 PartDescriptionQ3938-60132Scanner - Entire scanner - Does not include power supply, boards, and cableCE664-69004Scanner_Assembly - Scanner assembly - Does not include power supply, boards, and cableQ3938-60161Scanner_Assembly - Entire scanner - Does not include power supply, boards, and cableQ3931-67935Fixing_Assembly - 110-127V FIXING ASS Y Kit Part NumberQ3931-67935Fixing_Assembly - 110-127V FIXING ASS Y Kit Part NumberQ3931-67914Fuser_Assembly - Fuser Assembly - For 110 VAC to 127 VAC - Bonds toner to the paper with heat.Q3931-67915Fuser_Assembly - Fussing assembly - For 220 VAC to 240 VAC - Bones toner to the paper with heatQ3938-67901Carriage - Carriage assembly - Holds and positions print cartridgesQ3931-67927Fuser_Assembly - Fussing assembly - For 220 VAC to 240 VAC - Bonds toner to the paper with heatRM1-3244-000CNFuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 220VAC to 240VAC (+/- 10%) operationQ3938-67960PC_Board - Formatter (main logic) board - For HP Color Laserjet CM6040 seriesRM1-3307-040CNBelt - Intermediate transfer belt (ITB) assemblyRM1-3242-000CNFuser_Assembly - Fuser Assembly - Bonds toner to paper with heat - For 110VAC to 127VAC (+/- 10%) operationQ3938-67977PC_Board - Formatter (main logic) board - For HP Color Laserjet CM6040 seriesQ3938-67973Carriage - Carriage assembly - Holds and positions print cartridgesQ7719-67951Memory - HP 256MB 100-pin DDR DIMM - Used to add flash memory-based accessory fonts, macros, and patternsQ7720-67951Memory - HP 512MB 100-pin DDR DIMM - Used to add flash memory-based accessory fonts, macros, and patternsRM2-0190-000CNPower_Supply - Low voltage power supply ass yRM1-3594-000CNPower_Supply - Low voltage power supply assemblyRM1-4139-000CNPC_Board - Main controller PCA assembly - For the stapler/stacker and booklet maker unitRM1-4178-000CNSaddle - Saddle stapler assemblyQ3931-67902Memory - 128MB, 167MHZ, 200-pin DDR DIMM memory moduleRM1-4101-000CNTray - Stapler/stacker tray - Upper tray assembly for the stapler/stacker (output bin 1)Q3931-67907Scanner_Assembly - Laser/scanner assembly kitCC516-69002Transport_Module - Intermediate paper transport unit (IPTU) (whole unit)RM1-4102-000CNTray - Upper stack tray assembly (output bin 1) - For the booklet maker unitCB380-67901Drum - HP CLJ Blk Print CartridgeCB386-67901Drum - Hp color laserjet yellow image drumCB387-67901Drum - Hp color laserjet magenta image drum4G3-0670-000CNMount - Motor mount assemblyCB385-67901Drum - Hp color laserjet cyan image drumQ3938-67965Transfer_Kit - Image Transfer Kit 150KRM1-3307-000CNBelt - Intermediate transfer belt (ITB) assemblyCB381-67901Cartridge - Cyan print toner cartridge - For the Color LaserJet CP6015 seriesCB382-67901Cartridge - Yellow print toner cartridge - For the Color LaserJet CP6015 seriesCB383-67901Cartridge - Magenta print toner cartridge - For the Color LaserJet CP6015 seriesRM1-6642-000CNPC_Board - DC controller PC board assembly - Mounts on the rear of the print engine frame on the right side of the formatter boardRM1-6642-040CNPC_Board - Replacement for part RM1-6642-000CN DC controller PC board assembly - Mounts on the rear of the print engine frame on the right side of the formatter boardRM1-6642-090CNPC_Board - Assembly-DC Controller PCB R1.84RM1-6642-080CNPC_Board - Assembly-DC Controller PCB R1.84Q3938-67963Panel - Control panel assembly - Control buttons and display located on top front of printerQ3938-67910Power_Supply - Power supply assemblyQ3931-67911Drive_Assembly - Main drive assembly - Mounts on the right side of the printer - Metal plate with gears attached - Also known as main gear drive assemblyRM1-6642-060CNDC_Controller - Dc controller pcb ass'yRM1-6642-050CNPC_Board - DC controller PC board assembly - Mounts on the rear of the print engine frame on the right side of the formatter boardCB387ADrum - Hp color laserjet magenta image drum 824aCB385ADrum - Hp color laserjet cyan image drum 824aCB386ADrum - Hp color laserjet yellow image drum 824aRM1-4105-000CNTray - Lower stack tray assembly (output bin 2) - For the stapler/stacker and booklet maker seriesQ3938-67902PC_Board - Scanner controller-board (SCB) assembly - Provides timing and control for the flatbed scannerFM2-0721-000CNStacker_Assembly - Staple assembly - For stapler/stacker and booklet-maker unitRM1-4140-000CNPC_Board - Saddle controller PCA assemblyFL2-0846-000CNStacker_Assembly - Stapler unit - Located on the saddle stapler assemblyCB463ATransfer_Kit - HP Color LaserJet Transfer Kit. CP6015/CM6030/CM6040 TRNFR Kit prints approximately 150, 000 pagesRM1-4395-000CNGuide - Intermediate upper feed guide assemblyQ3931-67912Drive_Assembly - Toner cartridge drive assembly - Metal plate with gears attached - Provides movement to the cyan and black cartridgesQ3701-60020PC_Board - Modem PCA - HP LaserJet analog fax accessory 300Q3701-60014Fax_Module - Fax printed circuit assembly (PCA) - Accessed from the rear of the unit - Located on the formatter boardFM2-0722-000CNStapler - Stapler sub-assembly - Includes upper and lower clinch guide, staple unit and motor (M14), bin sensor flag, photo interrupter (PI46), and staple mountRM1-4109-000CNFeeder - Saddle paper feeder assembly - Includes saddle motor assembly and lower entrance guide assembly - For the booklet makerRM1-3652-000CNReversing_Unit - Reversing assembly for duplexer assemblyQ3931-67913Drive_Assembly - Toner cartridge drive assembly - Metal plate with gears attached - Provides movement to the yellow and magenta cartridgesCB380ADrum - Hp color laserjet black print cartridge 823aRM1-4136-000CNFeeder - Saddle paper feeder assembly - Includes saddle motor assembly and lower entrance guide assembly - For the stapler/stackerRM1-3686-000CNGuide - Intermediate lowerr feed guide assemblyCB384-67901Cartridge - Black print toner cartridge - For the Color LaserJet CP6015 seriesRM1-3333-000CNDoor - Right door sub assemblyRM1-4125-000CNTray - Operation-tray assembly - Includes operational tray cable and photo interrupter (TLP1242)RM1-3293-000CNDelivery - Face down paper delivery assemblyQ3938-67978Hard_Drive - Hard drive - High performance EIO serial ATA hard driveRM1-3665-000CNFeeder - Duplexing feed assemblyQ3931-67918Tray - 500-sheet paper input tray cassette - For use with tray 2Q3938-67961Hard_Drive - Hard drive - High performance EIO serial ATA hard driveQ7718-67951Memory - 128MB, 100-pin, DDR SDRAM DIMM memory moduleQ3931-67923Tray - 500-sheet paper input tray cassette - For use with Tray 3, 4, or 5Q3931-67919Roller - Paper pick-up roller and retard roller kit - Includes one pick-up roller, one retard roller, and two paper feed rollers - Use with tray 2,3,4, and 5Q3931-67938Roller - Paper pick-up roller - Includes one pick-up roller, and two paper feed rollers - Use with tray 2,3,4, and 5RM1-3529-000CNTray - 1 x 500-sheet input tray cassetteRM1-3218-000CNPower_Supply - Fuser power supply assemblyRM1-5475-000CNPC_Board - High voltage transfer |B| PCA assemblyRM1-3582-000CNPC_Board - High voltage transfer |A| PCA assemblyRM1-4119-000CNCover - Middle height cover assembly for the booklet maker unit4G3-0671-000CNPlate - Inner side plate assembly - Used on the booklet market series onlyRM1-4408-000CNCover - Rear cover assembly - Plastic cover that protects the rear air ductRM1-3206-000CNPickup_Assembly - Paper cassette pick-up assembly - Includes 1 pick roller and 2 feed rollersRM1-3533-000CNPickup_Assembly - 1 x 500-sheet input tray paper pick-up assemblyQ3938-67969Maintenance_Kit - ADF maintenance kit - Includes the ADF paper pick-up roller assembly and the separation pad assemblyQ3938-67944Maintenance_Kit - ADF maintenance kit - Includes the ADF paper pick-up roller assembly and the separation pad assemblyRM1-3345-000CNPickup_Assembly - Multi-purpose/tray 1 paper pick-up assemblyRM1-3357-000CNCover - Front cover assembly - Plastic cover that protects the front door assemblyFM2-0730-000CNPressure_Assembly - Pressure roller assembly - For the stapler/stacker and booklet-makerQ3938-67964Tray - Duplex switchback trayRM1-3569-000CNPC_Board - 1 x 500-sheet input tray paper feed PCA assemblyRM1-4108-000CNGuide - Swing guide assembly - Includes swing roller assembly, swing jam clearing label, swing press assembly, swing roller shaft assembly, and the paper delivery gate armRM1-3585-000CNPC_Board - Memory tag PCA assemblyRC2-1278-000CNCover - Rear cover - Plastic cover that protects the rear part of the stapler/stacker unitRM1-3222-020CNLifter - Lifter-drive-assemblyRM1-4172-000CNGuide - Entrance upper guide assembly - For the stapler/stacker and booklet maker unit4G3-0769-000CNMotor - Ejection stack motor (M32) assemblyRM1-4130-000CNDelivery - Saddle paper delivery assemblyFM2-0756-000CNGuide - Saddle guide assembly - Mounts on the front saddle side plate - For the booklet makerRC1-9871-000CNCover - 1 x 500-sheet paper input tray rear coverRM1-4135-000CNGuide - Lower height guide assemblyFM2-1409-000CNMotor - Press motor (M36) assembly4G1-2283-000CNCable - Cable, saddle unitRM1-4104-000CNTray - Stack tray assembly - Includes front and rear extension tray guide, stack tray, and extension trayRM1-4404-000CNCover - Internal front door cover assembly - Plastic cover located behind the front door assemblyRM1-3683-000CNCover - Lower left side cover assembly - Located on the intermediate feed main bodyRM1-3232-000CNCase - Thermopile case assembly4A3-1783-000CNRoller - Roller, foldingRL1-1477-000CNCover - Lower internal cover assembly - Internal cover for the saddle assembly - For the booklet maker unit onlyCB459ARoller - 2nd transfer roller assembly - For the laserjet CP6015 and CM6030/6040 seriesRM1-3366-010CNDrive_Assembly - Drive assembly - For use with multi-purpose/tray 1RM1-4399-000CNGuide - Rear guide reader assemblyRM1-3341-000CNTray - Multi-purpose/tray 1 drop down door paper input tray assemblyRM1-4121-000CNDoor - Upper cover assembly - Top door located on the stapler/stacker assemblyRM1-4519-000CNMotor - Fuser DC motor (M11) assembly - Drives the fuser roller, the delivery roller, and the fuser pressure rollerQ3938-67959Roller - Paper pick-up roller - Includes one pick-up roller, and two paper feed rollers - Use with tray 2,3,4, and 5RM1-3253-000CNCage - Formatter board cage assembly - Metal shield and enclosure for the formatter boardFM2-0737-000CNMotor - Saddle motor assembly - Includes primary transfer roller disengagement motor(M9) and motor mountRL1-1210-000CNCover - Rear cover - Plastic cover that protects the rear part of the printerFG3-2887-000CNPC_Board - Tray driver PCA assemblyRM1-4123-000CNCover - Inner cover assembly - Inner cover located on the left side of the finisher main bodyRC2-1351-000CNCover - Lower internal cover (stapler/stacker only)Q3931-67905Cover - Face down cover - Output paper cover on top of the printer - Holds the paper after it has been printedRM1-4131-000CNGuide - Upper delivery guide assembly - For the saddle assemblyRM1-3537-000CNDoor - 3 x 500-sheet paper input tray right door assemblyRC1-9336-000CNCover - Left cover assembly - Plastic cover that protects the left side of the printerFG3-2892-000CNCable - Cable, solenoidRM1-4110-000CNGuide - Lower entrance guide assembly - Located on the saddle paper feeder assemblyRC1-9872-000CNCover - 1 x 500-sheet paper input tray left coverRC1-9351-000CNCover - Paper delivery coverRM1-3247-020CNGear - Fuser one way gear assemblyRM1-4129-000CNCover - Upper left cover assembly - Plastic cover that protects the upper left side of the booklet makerRC1-9350-000CNCover - Upper front cover - Large rectangle shaped plastic cover located on left side on the top of the printerRC1-9896-000CNCaster - Double lock front caster - For the 1 x 500-sheet paper input trayRC1-9921-000CNDoor - Stock door - For 1 x 500-sheet paper input tray4G3-0725-000CNGuide - Motor guide assembly - Located on the saddle assembly - For motor (M3)Q3931-67920Roller - Paper pick-up retard roller - Used for tray 1RM1-4397-000CNHardware - Right assist assemblyRM1-3238-000CNPlate - Cyan partition plate assemblyRM1-4396-000CNHardware - Left assist assemblyRM1-3235-000CNPlate - Yellow partition plate assemblyRC1-9874-000CNCover - 1 x 500-sheet paper input tray lower right coverRM1-3233-000CNCover - Left side wall cover assembly4H3-0370-000CNClutch - Electromagnetic shutter clutch (CL31) connector (J1046)RM1-3564-000CNCable - Motor cable - For media feed stepping DC motor (M201)RL1-1272-000CNArm - Auxiliary arm - Mounts on the drive frame on the intermediate paper transfer unit (IPTU)RM1-3563-000CNCable - Motor cable - For media feed stepping DC motor (M202)RC1-9666-000CNCover - Back cover - Located on top of the shield plate on the intermediante feed main bodyRM1-3354-000CNPlate - Rear mount cover plate assemblyRC1-9882-000CNStopper - Stopper, right doorRK2-1366-000CNMotor - Toner feed motor (M17) - Drives the yellow, magenta, and cyan toner feed screws and waste toner feed screws - Mounts on the toner cartridge drive assemblyRM1-3237-000CNPlate - Magenta partition plate assemblyRM1-3291-000CNGuide - Multi-purpose/tray 1 guide assemblyRM1-3612-000CNCable - Fixing joint cable4G3-0934-000CNSensor - Paper face sensor assemblyRU5-6035-000CNGuide - Tray roller guide - Located on the output bin 1RM1-0037-020CNRoller - Paper feed/seperation roller assembly - Black rubber roller on a blue plastic cylinderRC2-1283-000CNPanel - Upper height panel - Located on the stapler/stacker unitRC1-9695-000CNPlate - Assist arm cap plate - Located on the upper guide assemblyQ7829-67903Motor - PCA motor assemblyRL1-1280-000CNCover - Right lower cover assemblyRM1-4107-000CNSensor - Area sensor flag assembly - Includes flag area sensor plate - Located on the finisher main bodyRM1-3618-000CNCable - Rear lower cableRM1-3364-000CNFan - Exhaust fan assembly - Cools the fuser areaRM1-3538-000CNDoor - 1 x 500-sheet paper input tray right door assemblyRC1-9917-000CNCaster - Stationary rear caster - Mounts on the bottom frame of the 500-sheet high capacity input (HCI) paper feeder assemblyFL2-0821-000CNSolenoid - Solenoid (SL34) - Buffer rear end holding solenoid drive signal4K1-1103-000CNMotor - Stepping motor (M5) connector (J113)4G3-1777-000CNCable - Staple connecting cable assemblyFM2-0763-000CNSensor - Rear end sensor assemblyFC5-5436-000CNRail - Rail rack - Mounts on the finisher main body - Four usedRL1-1311-000CNRail - Paper cassette tray left railQ7829-67909Foam - ADF reflector foam - White plastic sheet with foam that reflects the light wile scanningRM1-3570-000CNSensor - Option paper sensor PCA assemblyRM1-3252-000CNHolder - Main switch (SW11) holder assemblyRC1-8519-000CNTorque_Limiter - Torque limiter - Located next to paper pick-up retard roller in multi-purpose/tray 1 assemblyXF2-1608-840CNBelt - Timing belt - Located on the return roller assemblyRC1-9883-000CNLever - Lock lever - This is the rear cover lock for the 1 x 500-sheet paper input trayRM1-3610-000CNCable - DC controller board power cableRM1-3230-000CNHolder - Transfer contact holder assemblyRC1-9900-000CNSupport - Lock shaft support - Located on the 1 x 500-sheet paper input tray4S3-2117-000CNSpring - Tension spring - Provides tension to the front pressure plate (big spring)4G1-2285-000CNCable - Sensor cable - Located on the saddle tray assembly - Connects on the photo interrupter (TLP1242)RC2-1315-000CNCaster - Caster - Used on pedestal assembly (universal)RM1-3340-000CNTray - Face down end tray assemblyRL1-1284-000CNCover - Top cover assembly - Protects the top part of the main printer chassisFM2-0720-000CNMount - Flexible cable mount assemblyFM2-1708-000CNSensor - Option sensor assembly - Includes the photo interrupter (TLP1424) and bracketRL1-1310-000CNRail - Right cassette rail - For the 1 x 500-sheet paper input trayRM1-4394-000CNFan - Chassis fan assembly - Located on the intermediate feed main body - Includes fan and plastic fan bracket (FM8)RC1-9873-000CNCover - 1 x 500-sheet paper input tray upper front cover4G3-0210-000CNLock - Upper cover lock assembly4S3-0171-000CNGear - 50-tooth gear - Located on the saddle assemblyFM2-1417-000CNSensor - Sensor/switch assembly - Includes leaf spring, micro switch (MSW31), photo interrupter (PI32), and wire saddleRK2-1382-000CNFan - Delivery unit cooling fan (FM7)RC2-1284-000CNGuide - Side wall guide - Mounts on the upper height panel on the booklet maker unitRM1-3682-000CNGear - Damper gear assembly - Includes 70-tooth gear and one way hinge - Located on the damper assemblyRC1-8526-000CNGuide - Multi-purpose/tray 1 upper guideRM1-4398-000CNGuide - Front guide reader assemblyRM1-3620-000CNCable - Scanner joint cableRM1-4411-000CNArm - T2 guide arm assemblyQ7829-67917ADF - ADF float assemblyRM1-3617-000CNCable - Front cableRM1-3619-000CNCable - Rear upper cableXF2-3837-340CNBelt - Timing belt - Belt that runs on the 30-tooth pulley on the saddle assemblyRC1-9206-000CNRail - Rear reverse scanner railRM1-3254-000CNHolder - Cartridge contact holder assemblyQ3938-67952Hinge - ADF hinge assembly - For the top cover on the scanner (document lid)RK2-2376-000CNSensor - Sensor unit, humidityRL1-1335-000CNGuide - Guide, duplexing feed, upperFM2-0710-000CNSwitch - Approach switch assembly - Includes approach switch plate and microswitch (MS33)FM2-1423-000CNShaft - Swing press shaft assemblyFM2-0707-000CNSensor - Paper sensor assembly - Includes the paper sensor arm, photo interrupter (PI42), and paper sensor plateRC2-1347-000CNCover - Slide cover - Plastic cover that slide in to the upper height panel on the stapler/stacker unitFB3-7928-020CNDeflector - Paper deflector (flapper 1) - Shaft with curved deflector fingers - Attaches to the front and rear saddle side plateRC1-9706-000CNCover - Right cover assist - Located on the lower guide assemblyRL1-1283-000CNGuide - Multi-purpose/tray 1 right guide assemblyRM1-3239-000CNCover - Right side wall cover assemblyRL1-1322-000CNCover - 1 x 500-sheet paper input tray right front coverRC1-8959-000CNGuide - Guide, face-down innerRL1-1321-000CNCover - 3 x 500-sheet paper input tray right front coverRC1-9511-000CNCover - Cover, motorRC1-9278-000CNHolder - Fuser fan holder - Holds fan (FM2)RC1-9344-000CNCover - Left rear cover - Plastic cover that protects the left rear part of the printer - Corner cover with slot for I/O connectorsRM1-3216-000CNHolder - Intermediate transfer belt (ITB) gear holder assemblyFC5-3657-000CNTorque_Limiter - Torque limiter - Torque limiter for the swing press shaftRK2-1331-000CNMotor - Stepping motor - Main drive motor for the printer - Motor M1RM1-4415-000CNCover - Rear right cover assemblyFM2-1639-000CNMount - Delivery switch mount assemblyRL1-1289-000CNRoller - Paper pick-up roller - For the 1 x 500-sheet and 3 x 500-sheet paper input trayRM1-4392-000CNRoller - Retard roller - Mounts on the multi-purpose roller assembly next to the limiter torqueFB5-2697-000CNDeflector - Paper deflector (flapper 2) - Shaft with curved deflector fingers - Attaches to the front and rear saddle side plateRM1-4128-000CNMount - Lattice cable mount assemblyRM1-4407-000CNGuide - Paper delivery guide assemblyRM1-4409-000CNCable - Fuser bias cable assembly4S3-1050-000CNBearing - Ball bearing (6902ZZNR)RK2-1377-000CNFan - Cooling fan - Provides air to the print cartridge and imaging drum areaRC1-9705-000CNCover - Left cover assist - Located on the lower guide assemblyFM2-0709-000CNHolder - Area sensor holder assemblyRC2-1280-000CNCover - Lower left cover - Mounts on the saddle tray assemblyQ3931-67925Lock - Security lock adapter kitRK2-1378-000CNFan - Fuser cooling fan (FM2) - Provides air to the fuser area4G3-0271-000CNLink - Slide link assembly - Located on the top door assembly (upper cover)4S3-2116-000CNSpring - Tension spring - Provides tension to the front pressure plate (small spring)4G1-1498-000CNSensor - Area sensor PCA assembly - Located on the area sensor holder assemblyRC1-9884-000CNDoor - 1 x 500-sheet paper input tray tape doorFG3-2903-000CNCable - Cable, operation trayRK2-1356-000CNCable - Flexible flat cable - Connects to the formatter board through the (J9001) connector and to the DC controller PCA through (J123) connectorRM1-3561-000CNCable - Intermediate paper transfer unit (IPTU) drawer connector cable assembly - Located on the fin lock assemblyRC1-9881-000CNGuide - 1 x 500-sheet input tray paper feed roller guideRM1-3225-000CNGrip - Front grip support assemblyRM1-3226-000CNGrip - Rear grip support assemblyRM1-5950-000CNCover - Fuser fan cover assembly - Plastic cover located next to the rear cover assemblyFU5-0454-000CNGear - 40-tooth gear - Runs on the swing press shaft assembly - Located between torque limiter and bushing on the rear side plate of the finisherRM1-4401-000CNDuct - Intermediate transfer belt (ITB) duct assemblyRK2-1370-000CNMotor - Toner feed motor (M16) - Drives the black toner feed screws and waste toner feed screws - Located on the toner cartridge drive assemblyFC5-4221-000CNGuide - Tray roller guide - Mounts on the front side tray plateRL1-1215-000CNRail - Right cassette rail - For the 1 x 500-sheet paper input trayRC1-9276-000CNDuct - Cartridge duct - Plastic duct that vents air from the fan (FM3) to the cartridge areaRC1-9912-000CNShaft - Lock shaft - For the 1 x 500-sheet paper input trayRC1-9318-000CNCable - Guide, cable, eRC1-9277-000CNHolder - Cartridge fan holder - Holds fan (FM3)RM1-3391-000CNCable - Face-down unit 2 cableRM1-4141-000CNPC_Board - LED PCA assembly - Located on the stapler/stacker unit rear coverRM1-4402-000CNHolder - Tag PCA holder assemblyRM1-3599-000CNCable - MFP AC cable - Has connector J3005 on one side and J301 on the otherRC1-9309-000CNDuct - Scanner fan duct - Directs air into scanner areaRL1-1213-000CNRail - Left top rail - For the 1 x 500-sheet paper input tray4A3-1779-000CNPlate - Rotation plate - Located next to the dowel pin on the saddle assemblyRM1-4391-000CNFlag - Face down full flag assemblyRL1-1206-000CNRoller - Pick-up roller - Located on the on the paper pick-up plate assemblyRM1-3571-000CNCable - Paper pick-up option drawer cableRC1-9308-000CNCable - Guide, cable, cRM1-3623-000CNCable - Interface joint cableRC1-9607-000CNGuide - Hold guide plate - Located on the left side of the lower guide assemblyRC1-9703-000CNPlate - Rear mount cover plate assemblyFM2-1401-000CNSensor - Shutter sensor assembly4G3-1624-000CNSensor - Paper face sensing assembly - Located on the upper height panelRC1-9915-000CNBushing - Bushing - Mounts on the lock shaft next to the arm lock on the 1 x 500-sheet paper input tray4A3-1955-000CNPlate - Grounding plate - Used only for booklet maker seriesWG8-5696-000CNSensor - Photo-interrupter sensor assembly (Does not include the sensor flag)RM1-4400-000CNGuide - Guide sensor assembly - For fuser open cover detection sensor (SR34)FB3-7881-000CNKnob - Knob - Mounts on the lower internal cover on the left side of the saddle assemblyRM1-3624-000CNCable - Color plane registration joint cableFC5-6978-000CNPlate - Plate, option tray, frontRC1-8527-000CNCover - Multi-purpose/tray 1 blanking coverRC1-9211-000CNCover - Cover, main switchRM1-3560-000CNCable - Drawer cable - Locaten on the fin lock assembly in the intermediate feed main bodyRC1-8961-000CNDuct - Air duct - Deflects air from fan FM7XF9-0748-000CNBelt - Timing cogged belt - Located on the front side plate on the finisher main bodyRC1-9043-000CNDoor - Band, doorRG5-1928-000CNCable - Registration cable assembly - Includes 7P and 3P connectorsRC1-9334-000CNDuct - Duct, scannerRK2-1354-000CNCable - Laser flexible flat cable - Connects the laser driver PCA through (J501B) connector and the DC controller PCA through (J127) connectorRM1-5953-000CNCover - Front internal small cover assembly - Located on the upper right side of the front door assemblyRM1-5030-000CNCable - Cable, tp/t2 open sensorRC1-9649-000CNCover - Blanking cover - Located next to the four bushings on the drive frameRM1-3573-000CNCable - Pick-up option PCA connect cableRM1-3217-000CNCable - Fixing motor cableRM1-3622-000CNCable - Panel joint cableFC5-5004-000CNSensor - Paper sensing sensor flag - Mounts on the lower height panelRC1-9307-000CNCable - Guide, cable, bRC1-8928-000CNLever - Paper sensing lever - Senses paper in intermediate transfer belt (ITB) duct assemblyFU5-0457-000CNGear - 17-tooth gear - Attaches to the rear tray side plateRC2-1279-000CNCover - Connector tray cover - Mounts on the upper left side of the rear cover on the stapler/stacker unitVS1-7257-012CNConnector - Drawer Connector (J1903) - For the 1 x 500-sheet input trayRC1-8511-000CNRetainer - Retainer (C Type) for Color LaserJet CP6015n.FU5-1169-000CNBushing - Bushing - Attaches to the rear tray side plate - Located next to the 26-tooth gear on the tray drive shaft assemblyFC5-5024-000CNKnob - Latch knob - Mounts on the open/close guide on the saddle guide assemblyFS6-0829-000CNGear - 16/56-tooth gear - Runs on the folding roller next to the front adjustment armRC1-9190-000CNPlate - Plate, fan fixing, frontRM1-3574-000CNCable - Option sensor PCA connect cableFU5-9059-000CNScrew - M3 X 6mm machine thread screw with attached washer - Used to secure metal to metalRM1-3389-000CNCable - Control Panel cableXF2-1607-860CNBelt - Timing cogged belt - Runs on ejection stack motor assembly (M32)FM2-0718-000CNFlag - Entrance sensor flag assembly - Includes the entrance sensor lever and the entrance sensor arm damperQ7829-67914Sensor - ADF photo interrupter sensor with connectorRC1-9186-000CNGuide - Intermediate transfer belt (ITB) rear entrance guideRC1-9306-000CNCable - Guide, cable, aRC1-9332-000CNGuide - Fuser cable guide - Located on the fuser power supply assemblyFB3-7934-000CNRack_Slide - Rear rack slide - Mounts on the rear saddle side plateFB3-7967-000CNRack_Slide - Front rack slide - Mounts on the front saddle side plateRM1-3385-000CNCable - Toner feed motor (M16) cableRC1-9246-000CNPlate - Front sensor plate - For sensor (SR32)RM1-3576-000CNCable - Pick-up option lifter unit cable5851-2501Cable - Hard drive power SATA cable - Provides power to the hard drive connects to the mother boardFU5-0435-000CNGear - 44-tooth gear - Mounts on the front tray side plate attached to the upper tray cross memberRC1-9312-000CNCable - Guide, cable, dWC2-5512-000CNSwitch - Detection switch4A3-1763-000CNArm - Front adjustment arm - Located on the folding roller on the saddle assembly4A3-1764-000CNArm - Rear adjustment arm - Located on the folding roller on the saddle assemblyFS5-3576-000CNGear - 30-tooth gearRC1-9688-000CNGuide - Cable guide - Located next to the paper feed cogged belt on the intermediate feed main body4A3-1782-000CNStop - Lever stopperRU5-0790-000CNGear - 83/25-tooth gear - Mounts on the fuser motor plateRC1-9913-000CNArm - Lock arm - For the 1 x 500-sheet paper input tray - Mounts on the lock shaftFU5-2399-000CNGear - 29-tooth gear - Runs on the paper feeder motor assemblyFS5-3577-000CNPulley - 39-tooth pulley - Runs on the woodruff roller - Located next to the roller flagRC1-9326-000CNPlate - HVT-A (high-voltage transmission) guard plateRC1-8931-000CNRail - Rail, fixing, frontRC1-9360-000CNCover - Cover, face-down driveRC1-9256-000CNTray - Screw tray - Attaches next ot the cable guide ERC2-1356-000CNGround - Grounding plate - Located on the rear left side of the saddle assemblyRC2-1734-000CNLED - LED window - Mounts on the upper left side on the rear cover assembly of the stapler/stacker unitFS6-0830-000CNGear - 16-tooth gear - Runs on the folding roller next to the front adjustment armFU5-3086-000CNPulley - 20-tooth pulleyRM1-3630-000CNCable - Multi-purpose/tray 1 cableRU5-0868-000CNGear - 22-tooth gear - Small gear that runs on the paper-feed cogged beltFS6-0822-000CNGear - 16/33-tooth gear - Runs on the shaft located under the folding rollerRM1-3383-000CNCable - Toner feed motor (M17) cableRC1-9220-000CNLever - Lever, door interlock shutterRC1-9235-000CNPlate - Plate, drawer guardRC1-9300-000CNButton - Button, main switchRC1-9324-000CNHolder - Environment sensor holder - Holds the humidity sensor unitXD9-0234-000CNClip - E-Type retainer ringFB3-7980-000CNSpring - Torsion spring - Provides torsion to flag sensor located on the rear saddle side plateFU5-0428-000CNGear - 30-tooth gear - Runs on the timing belt on the finisher lower roller next to the 20-tooth pulleyFS6-0815-000CNGear - 32-tooth gear/16-tooth pulley - Located on the drive support in front of the motor (M5)FS6-2582-000CNSpring - Tension spring - Provides tension to the pressure plate assemblyFS6-0823-000CNGear - 16-tooth gear - Runs on the shaft located under the folding rollerFC5-5542-000CNGuide - Entrance sheet guide - Mounts on the cross member entrance guideFB3-7925-030CNFlag - Roller flag - Mounts next to the 39-tooth pulley on the saddle assemblyFB3-7973-000CNHolder - Roller holder 2 - For the cam shaftRM1-3575-000CNCable - Paper pick-up option cable - Used for the 1 x 500-sheet input trayXA9-1495-000CNScrew - Wafer head machine screw - M3, 6mm long, No. 2 Phillips recess - Secures metal to sheet metalXA9-0912-000CNScrew - Machine screw with captured washer - M5 X 12 - Typically used to secure plastic parts to metalXA9-1386-000CNScrew - M3 X 8mm long self threading screw with captured washerXA9-1422-000CNScrew - M4 X 12mm machine screw with washerXA9-1448-000CNScrew - Screw - M4 X 8mm longXA9-1449-000CNScrew - M3 pan-head Phillips screw with machine threads - 8mm longXA9-1469-000CNHardware - Machine screw with attached washer - M3, 10mm - Used to hold plastic to metalFC5-5021-000CNLatch - Right latch clawRC1-9687-000CNHardware - Blanking sheet - Mounts on the shield plateXA9-1500-000CNScrew - M3 pan-head Phillips screw with flat washer - 8mm longXD2-3100-152CNRing - C-type external retainer ringXD3-2300-142CNPin - Dowel pin - Located next to the 17-tooth gear on the output bin 2XD3-2300-202CNPin - Dowel pin - Locate next to the 50-tooth gearRC1-9244-000CNSpring - Torsion spring - Provides torsion to the front fuser fan plateRC1-9231-000CNRail - Roller, railRC1-9233-000CNSpring - Spring, leafRC1-8939-000CNRail - Rail, fixing, rearRC1-9208-000CNFoot - Chassis rubber footRC1-9901-000CNPlate - Switch cover plate - For the 1 x 500-sheet paper input tray door open detection switch (SW103)RC1-9328-000CNHolder - High voltage connector holder - Located on the left side of the printer chassis - Attaches behind the main switch coverRM1-3572-000CNCable - Pick-up option door switch cableFB3-7979-000CNFlag - Flag sensor - Located on the rear saddle side plateFB5-5937-020CNFlag - Flag sensor - Located next to the ball bearing (6902ZZNR) - Mounts on the rear saddle side plateFC5-5005-000CNSpring - Torsion spring - Provides torsion to the paper sensing sensor flag located on the lower height panel4A3-4715-000CNPlate - Stop hinge plate - Used only for booklet maker seriesRM1-5029-000CNCable - Cable, fixing open sensorXB4-7401-005CNScrew - M4 truss head (flanged) screw - 10mm long - Typically used to secure plastic parts to the left and right side platesXB4-7401-006CNScrew - M4x10 tapping pan-head screwXB6-7303-005CNScrew - Machine screw - M3, 30mm long with self-tapping threads - Typically used to hold metal to plasticWT2-5694-000CNClamp - Snap-in cable clampWT2-5738-000CNHolder - Cable holder - Secures cable at left front side near DC controller board - White plastic stand-off/holderRU5-0791-000CNGear - 34-tooth gear - Mounts on the fuser motor plateRU5-2796-000CNSpring - Tension spring - Provides tension to the paper sensing leverRU5-2822-000CNSpring - Tension spring - Provides tension to the scanner assemblyVS1-7177-003CNClip - Retaining clip - This is a retaining clip for fuser thermistor power cableXA9-1504-000CNScrew - M3 truss head (flanged) screw - 8mm longXA9-1801-000CNScrew - M13x12 RS screw - Used to secure metal to metalXB1-2300-407CNScrew - M3x4 machined truss-head screwXD9-0240-000CNPin - Pin, dowelRL1-1216-000CNPlate - Fuser motor (M11) plateRS5-9099-000CNScrew - Stepped screw - Larger shoulder screw used to fasten the left side cover to the frame of the 2,000-sheet paper feeder assembly (two used)FS6-0814-000CNGear - 16-tooth gear/32-tooth pulley - Located on the rear part of the lower pass guide next to the 32-tooth gear/16-tooth pulleyRC1-9620-000CNPulley - Flange pulley - Attaches to the paper feed cogged belt located on the intermediate feed main body assemblyRC1-4585-000CNBushing - Bushing - Located on the side cover assembly (four needed)RC1-8567-000CNRoller - Multi-purpose paper pick-up rollerQ7829-67924Roller - Pickup roller high capacity input (HCI) - Attached to the pickup arm - Presses down the paper stack surface to feed the paper one sheet at a time (white)Q3938-67970Cover - ADF jam access cover - Located on the left top side of the printer - To remove paper jam from the ADFQ6998-67901Door - Front door assembly - For the stapler/stacker unitQ6998-67902Tray - Top output bin tray - Stack sub-tray assembly for the stapler/stacker unitQ6999-67901Door - Front door assembly - For the booklet maker unitQ7542-60003PC_Board - Formatter (main logic) board - For HP Color Laserjet CM6040 seriesQ3938-60107Overlay - Control panel overlay - Snaps on top of the control panel assembly (English)Q3938-67953Diverter - ADF diverter assembly - Diverts paper to duplexer assembly, face up tray or face down delivery assemblyQ3938-67954Cover - Roller cover - Plastic cover that protects the ADF pick-up rollerRM1-4113-000CNTray - Booklet-output bin (saddle tray assembly) - Includes sensor cable and photo interrupter (TLP1242)Q3931-67906Filter - Air filter kitQ3938-67945Cover - ADF rear end cover assembly - End cover (cap)Q3938-67946Cover - ADF front end cover assembly - End cover (cap)Q3938-67948Cable - ADF cable assembly - Interconnects the ADF assembly to the flatbed scanner assemblyQ3938-67949Pad - ADF separation pad assembly - Helps separate paper in the ADFQ3938-67950Tray - ADF input paper tray assembly - Holds 50-sheetsQ3938-67951Flag - ADF paper sensor flagQ3938-67905Inverter - Inverter assemblyQ3938-67906Glass - Scanner glass assembly - Glass plate on which the documents are placed to be scanned - Mounts in the scanner bezelQ3938-67907Sensor - Scanner lid sensor assemblyQ3938-67908Motor - Scanner motor - Drives the optical carriage assemblyQ3938-67909Pulley - Scanner pulley assembly - For transmission timing beltQ3938-67911Rod - Scanner rod - Shaft that the scanner carriage assembly rides onQ3938-67915Guide - Rubber guide - For the scanner glassQ3938-67920Cover - Upper cover - Plastic cover that protects the upper left side of the ADF unitQ3938-67921Cover - ADF lower cover - Plastic cover that protects the lower left part of the ADF unitQ3938-67922Cover - Upper cover - Plastic cover that protects the upper right side of the ADF unitQ3938-67923Cover - ADF lower cover - Plastic cover that protects the lower right part of the ADF unitQ3938-67924Cover - ADF top cover - Plastic cover that protects the top part of the ADF unitQ3938-67925Cover - ADF rear cover - Plastic cover that protects the rear part of the ADF unitQ3938-67926Cover - Front cover - Plastic L-shaped cover were control panel snaps onQ3938-67927Cover - Plastic screw covers with an adhesive back - Covers screw heads that secure the plastic scanner top coverQ3938-67928Hardware - Power supply harnessQ3938-67935Belt - Transmission timing belt - Maintain constant speed during power transmission - Located on the trasmission assemblyQ3938-67937Fan - Cooling fan - Fan that cools the scanner controller board (SCB) area