HP Color LaserJet 1500L Parts

Color_LaserJet  - HP Color LaserJet 1500L Printer

Fuser_Assembly  - Fuser Assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat

Fuser_Assembly  - Fuser Assembly (For 220V to 240V operation) - Bonds the toner to the paper with heat - Slides in and locks in lower rear of printer

Laser_Scanner  - Laser/scanner assembly

Laser_Scanner  - Laser/scanner assembly

Drum  - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print ONLY, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages)

Fuser_Assembly  - Fuser Assembly (For 110V to 127V operation) - Bonds the toner to the paper with heat

Drum  - Imaging drum/transfer assembly cartridge - Inserts into printer through the top door - Life expectancy is 20,000 pages for black print only, 5,000 pages for color (Typical combined life is approximately 6,000 to 8,000 pages)

PC_Board  - DC controller board - Mounts on the left side of the printer (Behind the formatter board assembly)

Print_Server  - JetDirect 175X external print server - Has one 4-pin USB connector and one RJ-45 LAN connector - Connects to the printer via the USB port and the network via the LAN port

Power_Supply  - Low voltage power supply - For 110V to 127V AC operation - Includes the AC power input connector and power switch

Cartridge  - Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage

Cartridge  - Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage

Cartridge  - Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage

Power_Supply  - Low voltage power supply - For 220V to 240V AC operation - Includes the AC power input connector and power switch

Carousel  - Carousel (Rotary) assembly - Includes the carousel assembly, the support assembly, end plates, drive gears and shaft, sensors, and cables

Cartridge  - Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage

Sideplate  - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701)

PC_Board  - Formatter board only - Does not include the metal formatter cage covers

Drive_Assembly  - Rotary drive assembly - Includes the carousel rotating motor (DCM703), toner cartridge drive motor (PM705), developing rotary stopper solenoid (SL93), bracket, and gears

Cartridge  - HP Color LaserJet smart Cyan print cartridge - Will print approximately 5,000 pages at 5% coverage

Cartridge  - HP Color LaserJet smart Yellow print cartridge - Will print approximately 5,000 pages at 5% coverage

Cartridge  - HP Color LaserJet smart Magenta print cartridge - Will print approximately 5,000 pages at 5% coverage

Sideplate  - Right rear side plate assembly - Includes the rear half of the metal right side plate, the Fuser Assembly drive motor and the three associated gears

Sideplate  - Right side plate assembly - Includes the front half of the metal frame assembly, gears, imaging drum/transfer assembly drive cams, cover engaging mechanism, roller engaging clutch (CL2), and main drive motor (DCM701) - Mounts on the right side

Power_Supply  - High voltage power supply board (HVT) assembly - Has contacts for the eight high voltage springs in the printer

Cartridge  - HP Color LaserJet smart Black print cartridge - Will print approximately 5,000 pages at 5% coverage

Motor  - Main motor assembly - Large motor mounted on a controller PC board

Motor  - Main motor assembly - Large motor mounted on a controller PC board - Mounts on the inside of the metal right side frame assembly

Power_Supply  - Sub-high voltage board - Small auxillary PC board

Tray  - Multi-purpose front input tray assembly (tray-1) - Includes the front cover piece, pull-out paper support, and the flip-out extender

Cover  - Top cover assembly (blue plastic) - Includes the molded-in face-down output tray and the lift-up top cover door assembly

Motor  - Rotary motor assembly

PC_Board  - Carousel position and toner level photoelectric sensor PC board - 'L' Shaped PC board with the two sensors

Clutch  - Electromagnetic clutch assembly (24V) - Electrical clutch between the clutch drive gear and shaft

PC_Board  - Density photoelectric sensor PC board

Motor  - Stepping motor - 24V DC

Motor  - Stepping motor (24V)

Motor  - Stepping motor - 24VDC

Cable  - Cable assembly (two 3-pin connectors and a spad lug)

Power_Cord  - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 220V in Denmark)

Fan  - Cooling fan (Panaflo Model FBA08T24H - 80mm X 80mm X 15mm high, DC brushless, 24V DC, 190mA)

Roller  - Upper top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, two anti-reversing flaps, and the drive gear

Roller  - Lower top bin output roller assembly - Includes the shaft with four rubber rollers, two bushing/shaft retainers, and the drive gear

Sideplate  - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges

Cover  - Left side cover (Quartz Gray) - Does not include any attaching parts

Solenoid  - Solenoid assembly

PC_Board  - Carousel position and toner level photoelectric sensor PC board - 'L' Shaped PC board with the two sensors

Cable  - Cable assembly (two 3-pin connectors and a spad lug)

Cable  - Universal serial bus (USB) interface cable - Type 'A' connector to type 'B' connector - 2.0m (6.6ft) long

Pressure_Assembly  - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft

Pressure_Assembly  - Carousel pressure (support) assembly - Includes the main rear support, E-label reader assembly, engaging sensor, and the engaging rod shaft - Primary support structure for the toner cartridge carousel

Power_Supply  - Sub-high voltage board - Small auxillary PC board

Cover  - Left side cover assembly (Quartz Gray) plastic - Includes the power switch button, rod and spring (The power switch is located on the low voltage power supply board)

Guide  - Lower separation guide assembly - Includes the guide bracket, paper output sensor (PS1) and flag, exit drive shaft with two rubber rollers, shaft gear, and idler gear

Roller  - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1)

Roller  - Registration roller assembly - Includes the roller, bushings, mounting plate, paper sensor, and the sensor flag

Roller  - Transfer roller assembly - Long black foam type roller - Transfers static charge to paper

Cover  - Right side cover assembly (Quartz Gray) plastic - Includes the DIMM memory door

Tray  - Face-up output tray assembly - Includes the pull-down door and Fuser Assembly locking bracket (Does NOT include the lock releases)

Door  - Top cover door (blue plastic) - For accessing the toner cartridges and the imaging drum/transfer assembly - Mounts to the top cover frame

Guide  - Entrance guide assembly - Angled metal guide between the registration roller and the transfer roller

PC_Board  - Top of page photoelectric sensor PC board - Includes the photoelectric top of page sensor and the print engine test switch

Cable  - Cable assembly (two 7-pin connectors)

Door  - Memory access door (Quartz Gray perforated plastic) - Allows access to the printer memory slots - Mounts on the right side cover

Shutter  - Registration shutter assembly - Includes the metal roller, mounting frame, grounding springs, and the dual coupling gear

Control_Panel  - Control panel assembly (mechanical only) - Includes the 'Rotate Carousel', 'Cancel Job' and the 'Go' buttons, plus the various indicator light pipes - All switches and LED's are on the formatter PC board

Cable  - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101)

Cable  - Flat flexible cable (FFC) assembly - Connects between the formatter assembly (J1001) and the DC controller board (J101)

Roller  - Paper pickup roller assembly - Includes the shaft, guide assembly cams, the D-shaped roller, and roller retainers - Picks paper from the multipurpose front input tray (tray 1) - Mounts in the lower portion of the front frame assembly

Sideplate  - Left side carousel plate assembly - End plate under the rotational toner cartridge carousel - Includes all of the high voltage contacts for the toner cartridges - Mounts on the metal carousel support frame

Pad  - Separation pad assembly - Includes the separation pad, holder and spring

Guide  - Separation guide assembly - Includes the plastic guide, label, and the two small spring loaded rollers

Guide  - Left paper feed guide (small Black plastic arm)

PC_Board  - Registration sensor PC Board - Small board with flag activated photosensor

Power_Cord  - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 220V in Switzerland)

Reader  - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board

Guide  - Paper guide assembly - Paper width adjustable guide assembly for the multi-purpose front input tray (tray 1)

Bezel  - Interface bezel (Quartz Gray plastic) - Vertical cover that surronds the interface connectors

Cable  - Flat flexible cable

Plate  - Cover plate (metal)

Connector  - Connector assembly - For optional paper tray

Cable  - Cable assembly (two 4-pin connectors) with shield

Reader  - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board

Clip  - Cable clip - 'C' shaped White plastic

Plate  - Mounting/grounding plate

Cover  - Solenoid cover (Steel) - For magnetic wave sheilding

Bushing  - Bushing/shaft retainer assembly - Black plastic

Gear  - Gear assembly - Metal plate with two White plastic gears attached

Arm  - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open

Reader  - E-label reader (contact board ONLY) - Connects the cartridge nonvoliatile memory to the DC controller board

Support  - Laser/scanner support assembly (sheet metal plate)

Belt  - Feed guide drive belt - Small belt approximately 5/16 inch wide with 'A' shaped ribs on it

Power_Cord  - Power cord (Dove Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in the U.K., Hong Kong, Singapore, Malaysia)

Print_Server  - JetDirect 380X external IEEE-802.11b (Wi-Fi) wireless print server - Connects to printer using Universal Serial Bus (USB) cable

Print_Server  - JetDirect 310X external print server - Fast Ethernet Internet connector for sharing network peripherals with USB ports, in a 10/100 TX LAN environment - Has one USB printer port and one RJ-45 10/100 Base-TX connector

Power_Cord  - Power cord (dove gray) - 2.3M (7.5ft) long - Has straight (F) receptacle (For 240VAC in the United Kingdom, Hong Kong, Singapore, Malaysia)

Tray  - Face-Up output tray door (ONLY)

Tray  - Toner catch tray (curved Black plastic piece) - Holds residual toner from photosensitive drum

Thermistor  - Thermistor for HP Color LaserJet 2820 Series

Reader  - E-label reader assembly - Connects cartridge nonvoliatile memory to the DC controller board

Power_Cord  - Power cord (Flint Gray) - 18 AWG, 2.3m (7.5ft) long - Has straight (F) receptacle (for 120V in the USA, Canada, Mexico, Philippines, and Taiwan)

Cover  - Upper rear cover (Quartz Gray) - Mounts on the upper rear of the printer above the face-up output tray door

Airflow_Guide  - Airflow Guide (duct) - Black plastic insert piece which runs the width of the printer and has an air flow hole on right side

Hinge  - Tray hinge - For the left side of the multi-purpose front input tray (Tray 1)

Power_Cord  - Power cord (Flint Gray) - 2.3m (7.5ft) long - Has straight (F) receptacle (For 240V operation in Australia, New Zealand)

Guide  - Right paper feed guide (small Black plastic arm)

Cable  - Cable assembly (two 8-pin connectors, Purple wire)

Cable  - High voltage cable assembly (two 15-pin connectors and two 14-pin connectors)

Solenoid  - Solenoid assembly

Holder  - Holder - Housing for the fusing connector assembly

Cable  - Cable assembly - 'Y' type cable (three connectors) - The 14-pin connector splits into an 8-pin connector and a 6-pin connector

Cable  - Cable assembly (with seven connectors)

Roller  - Paper pickup roller ('D' shaped)

Guide  - Left cartridge guide assembly

Hinge  - Tray hinge - For the right side of the multi-purpose front input tray (Tray 1)

Gear  - Gear assembly - Metal plate with two White plastic gears attached

Connector  - Connector assembly - For optional bottom paper tray

Sensor  - Sensor PC board - Small board with flag activated photosensor

Switch  - Microswitch with lever activator

PC_Board  - Registration sensor PC Board - Small board with flag activated photosensor

Cover  - Front lower cover (blue plastic) - Front lower strip below the multi-purpose input tray - Has recessed area for the printer logo

Cable  - Cable assembly (two 2-pin connectors)

Power_Cord  - Power cord (Flint Gray) - 17 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 220V in Europe, Saudi Arabia, South Africa, India, and Korea)

Airflow_Guide  - Airflow guide (duct) / fan holder bracket assembly (Quartz Gray plastic)

Cover  - Face-down paper output L-Shaped cover ( Blue) - Serves as the rear of the tray for the face-down output tray on top of the printer

Cleaner  - Toner cleaning cloth - Specially treated cloth for absorbing toner (1 per package) - Ideal for cleaning up toner spills

Damper  - Damper assembly (Gray plastic piece with small 13-tooth gear on it)

Connector  - Connector for the Fuser Assembly - Seven small contol pins plus three separated high current pins

Shaft  - Lock release shaft - Small shaft with locking tab - Does NOT include the lock release lever

Cover  - Roller cover - Covers the multipurpose paper pickup roller assembly - Mounts on the lower front of the front frame assembly

Cover  - Front inner cover (Blue) - Mounts on the front frame above the multi-purpose input tray

PC_Board  - Waste toner sensor PC board - Small board with an LED and photoelectric sensor - Monitors the level of the excess toner deposited in the imaging drum/transfer assembly

Cable  - Front cable assembly (six connectors)

Bushing  - Support bushing

Plate  - Transfer slide plate - Small 'U' shaped metal insert plates

Rack_Slide  - Rack slide - White plastic piece with gear teeth layed out in rack form on both sides

Arm  - Top cover rack arm (Black) - Plastic arm with teeth on bottom edge - Disengages the imaging drum/transfer assembly drive cams when the top door is open

Belt  - Paper feed belt - Small black rubber belt approximately 1/8 inch wide with little 'A' shaped ribs on it

Spring  - Right retaining spring - Helps to secure and ground the imaging drum/transfer assembly in the printer

Insulator  - Insulating sheet (Transparent plastic)

Plate  - Feed plate - Center metal plate with slots that the ribs on the middle frame assembly go through

Cable  - High voltage cable assembly

Rod  - Power switch rod - Goes between the power button and the power switch on the low voltage power supply board

Pulley  - Pulley roller (accommodates one feed belt) - Small black roller approximately 1.59cm (5/8 inch) long with one ball type pulley

Gear  - 22 tooth gear (Black plastic) - Small gear with diagonally cut teeth

Spring  - Torsion spring for HP Color LaserJet 2500 Series

Flag  - Sensor arm and flag - Activates the photosensor (Does NOT include the roller)

Bushing  - Right roller bushing - Acts as the bearing and retainer for the right end of the paper pickup roller assembly (tray 1)

Ground  - Grounding plate - Provides grounding for the top-of-page sensor and shielding for the density sensor boards

Lever  - Right side lock release lever

Lever  - Left side lock release lever

Bushing  - Bushing/shaft retainer assembly (White plastic)

Bushing  - Shaft bushing for HP Color LaserJet 1500 Series

Spring  - Tension spring for HP Color LaserJet 1500 Series

Cable  - Cable assembly (8-pin, red wire)

Bushing  - Left roller bushing - Acts as the bearing and retainer for the left end of the paper pickup roller assembly (tray 1)

Cable  - Cable assembly (two 3-pin connectors)

Roller  - Belt roller - Small oval shaped roller approximately 1-3/4 inches long

Insulator  - Insulating sheet (Transparent plastic)

Plate  - Contact plate - copper clad metal spring - Holds the right end of the small 500 Meg-ohm resistor

Cable  - Cable assembly for HP Color LaserJet 1500 Series

Bushing  - Bushing for HP Color LaserJet 1500 Series

Spring  - Tension spring for HP Color LaserJet 1500 Series

Gear  - Dual gear - 26 tooth / 50 tooth (White plastic)

Support  - PC board support (Black plastic holder)

Guide  - Top output bin guide - Small curved ribbed black plastic piece

Spring  - Tray 1 flag spring - Provides torsion for the tray 1 paper sensor flag

Spring  - Left retaining spring - Helps to secure the imaging drum/transfer assembly in the printer

Flag  - Test print flag (Black lever)

Shaft  - Idler gear shaft - Short metal rod

Cable  - Cable assembly (two 5-pin connectors)

Cable  - Cable assembly (two connectors and two spade lugs)

Gear  - 30 tooth gear (White plastic)

Static_Dissipater  - Static eliminator ground plate - Right angled metal piece with small teeth on top edge

Spring  - Electrical contact spring

Cable  - Cable assembly (two 4-pin connectors) with shield - Connects between the cartridge drive motor and the DC controller board

Spring  - Compression spring

Gear  - 30 tooth gear (White plastic)

Gear  - Dual gear - 37 tooth / 43 tooth (White plastic)

Bushing  - Bushing assembly (black plastic bushing with small guide roller on top)

Spring  - Compression spring

Spring  - Electrical contact spring

Plate  - Contact plate - copper clad metal spring - Holds the left end of the small 500 Meg-ohm resistor

Pad  - Light blocking pad assembly - Black plastic frame with soft rubber gasket and stiff conductive Mylar piece (grounded)

Cable  - Cable assembly (four 3-pin connectors)

Cable  - Cable assembly (two 3-pin connectors)

Roller  - Sensor flag roller (small White plastic roller)

Roller  - Pressure roller (small Black hard plastic disk shaped roller)

Roller  - Pressure roller (small Black hard plastic 'solid' roller)

Spring  - Electrical contact spring

Pulley  - Pulley roller (accommodates three feed belts) - Small black roller approximately 3.49cm (1-3/4 inches) long with three ball type pulleys

Ground  - Grounding plate

Gear  - Dual gear - 20 tooth / 40 tooth

Gear  - 26 tooth gear (White plastic) - Has recess for shaft drive pin

Spring  - Electrical contact spring - Spring steel wire with compression springs formed on both ends

Guide  - Cable guide (Quartz Gray plastic)

Gear  - 51 tooth gear (White plastic)

Foot  - Rubber foot - Square self-adhesive rubber foot

Spring  - Torsion spring for HP Color LaserJet 1500 Series

Shield  - RFI shield - Parallel wire form mounted over the fan

Shaft  - Feed drive shaft - Long shaft with eight feed belt ball type pulleys and one ribbed feed guide drive belt pulley

Holder  - Interlock switch holder (Quartz Gray plastic) - Does NOT include the micro-switch

Spring  - Electrical contact spring

Gear  - 16 tooth gear (Black plastic) - Gear with large stop tooth and shaft lock tab

Cover  - Solenoid cover (Steel) - For magnetic wave sheilding - Mounts over the solenoid on the right side of the front frame assembly

Plate  - Contact plate for HP Color LaserJet 2500 Seriess

Spring  - Electrical contact spring

Spring  - Electrical contact spring

Clip  - Drawer connector - Connector located on bottom of tray assembly frame on right side, which connects tray assemblies to each other

Clip  - E-ring clip for HP Color LaserJet 1500 Series

Bushing  - Bushing (black plastic)

Gear  - 15 tooth gear with drive shaft (Black plastic)

Spring  - Electrical contact spring

Holder  - Sensor assembly mounting holder

Gear  - 26 tooth gear (Black plastic) - Has 1/8th portion of gear cut away

Flag  - Paper flag - Plastic rod with paper sensing flag on one end and sensor activator flag on the other

Cover  - Gear Cover (Small Black plastic cover) - Covers the left end of the feed drive shaft

Cover  - Cover - For the engaging motor (PM704) - Mounts on the upper left side of the rear frame assembly

Cable  - Grounding cable assembly

Gear  - Dual gear - 32 tooth / 37 tooth (White plastic)

NamePlate  - Nameplate - Color LaserJet 1500L printer logo

Screw  - Pan head machine screw with washer - M3.0 x 0.5, 6mm long, Number 2 Phillips

Paper  - LaserJet Satin finish tough paper - A size (8.5 x 11-inches) - Will not tear and will withstand outdoor weather conditions - Can print on both sides

Paper  - LaserJet Satin finish tough paper - A4 size (21.0cm x 29.7cm) - Will not tear and will withstand outdoor weather conditions - Can print on both sides - 50 sheets per box

Paper  - Gd: lj paper spec

Power_Cord  - Power cord (Flint Gray) - 16 AWG, 2.3m (7.5ft) long - Has straight (F) C13 receptacle (for 240V in Israel)

Service_Guide_PH  - HP Color LaserJet 1500 printer Service Manual - Includes troubleshooting, error messages, paper jams, parts and parts diagrams.